RF Hardware Electronics Designer

Albelissa Engineering, IT & Digital Solutions; Piemonte; In loco; EUR 40.000 - 50.000; Tempo pieno

Descrizione del lavoro

Albelissa Engineering, IT & Digital Solutions in Italy seeks a Hardware Electronics Designer to own RF front-end and antenna hardware for an X-band AESA radar payload used in in‑orbit Rendezvous and Proximity Operations. The role requires end‑to‑end hardware ownership and coordination with subcontractors.

You will lead RF hardware design, interface with software teams for HW/SW integration, and ensure qualification for space—adhering to ECSS guidelines and space environment constraints.

Competenze

• Bachelor’s or Master’s degree in Electronic, Telecommunications, or RF Engineering.
• 3+ years RF/microwave hardware design experience with real builds and measurements.
• Hands‑on RF testing with VNA, spectrum analyzers, and signal generators.
• High‑frequency PCB design with controlled impedance and RF layout.
• Experience owning a subsystem end-to-end and coordinating external suppliers.
• Proficiency in MATLAB, Python, or equivalent for RF modeling.

Mansioni

• Lead RF/microwave front-end design: T/R modules, LNAs, PAs, filters, mixers, switches, beamforming network.
• Design AESA antenna/phased array feed network with beam-steering capabilities.
• Produce RF PCB designs including impedance stack‑ups, RF routing, grounding, shielding, and cavity resonance mitigation.
• Define calibration approaches for phased array and RF chain.
• Lead hardware integration verification and validation from plan to in‑orbit validation.
• Characterize performance with RF lab equipment and correlate measurements with predictions.
• Coordinate with subcontractors for digital/FPGA boards, mechanical/thermal, and PCB fabrication.

Conoscenze

RF engineering

Front-end design

RF testing

MATLAB/Python

RF layout & PCB

Formazione

Bachelor’s or Master’s degree in Electronic/ RF Engineering

Strumenti

Altium

KiCad

ADS/AWR/HFSS/CST

Descrizione del lavoro

Company Description

Albelissa Engineering, IT & Digital Solutions is an international consulting company specializing in high-value engineering, IT, and digital outsourcing services. The organization focuses on delivering practical results and cost-efficient solutions that help clients address both daily operational needs and complex technical challenges. With a foundation in mechanical, electrical, and electronic engineering, research and technology development, embedded software, and IT & digital services, Albelissa supports clients through its worldwide centers of excellence. The company provides local and global outsourcing, including offshore services in India and China, to customers in Europe and North America. This global presence enables Albelissa to combine efficiency, quality, and cost savings for its partners.

Position Overview

We are seeking a Hardware Electronics Designer to own the design, build, and bring-up of the RF front-end electronics and antenna hardware for our in-house X-band AESA radar payload, used for in-orbit Rendezvous and Proximity Operations (RPO) and Close Proximity Operations (CPO). On our project, the RF front-end and the radar algorithms are the core in-house know-how; this role owns the hardware side end-to-end and coordinates subcontractors for the non-core boards and integration.

Key Responsibilities

• Lead the design of the RF/microwave front-end: T/R modules, LNAs, power amplifiers, filters, mixers, switches, and the beamforming network.
• Design the AESA antenna / phased array and feed network, including beam-steering and beamforming hardware.
• Produce RF PCB designs: RF distribution network, filters, controlled-impedance stack-ups, RF routing, grounding and shielding, and cavity / RF-resonance mitigation.
• Define and implement calibration approaches for the phased array and the RF chain.
• Lead hardware integration verification and validation from the strategy (V&V Plan, Test Plan preparation) up to the final product in-orbit validation.
• Characterize performance with RF lab instrumentation (VNA, spectrum / signal analyzers), correlating measured versus predicted with the RF performance / algorithms engineer.
• Interface with subcontractors for a wide variety of components and domains: digital / FPGA carrier boards, power / PCDU, mechanical and thermal, PCB fabrication and assembly, environmental testing.
• Hold the responsibility for the physical internal interfaces of the RADAR on the RF and digital / processing side (DPU, FPGA) and interact with the software team to maximize HW/SW integration.
• Support qualification for the space environment and document design work according to internal engineering standards.

Required Qualifications

• Bachelor’s or Master’s degree in Electronic, Telecommunications, or RF Engineering, or equivalent.
• 3+ years of experience in RF/microwave hardware design, including front-ends that were built and measured (not only simulated).
• Hands‑on experience with RF testing equipment: vector network analyzers, spectrum analyzers, and signal generators.
• High‑frequency PCB design (controlled impedance, RF layout) with a professional EDA tool (e.g., Altium, KiCad) and RF simulation (e.g., ADS, AWR, HFSS, or CST).
• Experience owning a subsystem end-to-end and coordinating external suppliers.
• Proficiency in MATLAB, Python, or equivalent tools for RF modeling and analysis.

Preferred Qualifications

• AESA / phased-array hardware experience and T/R module design.
• Antenna (patch array) design experience.
• Knowledge of space environment constraints, radiation effects, and component qualification principles (ECSS).

Key Competencies

• Strong hands‑on hardware instinct: design build measure debug.
• Ability to own a critical subsystem with limited supervision.
• Ability to work within a small multidisciplinary team and steer subcontractors.
• Good technical communication for reporting and documentation

Benefits

Wage & Benefits

Gross Wage (RAL): €40000 - €50000 based on experience and applicable skills