Injection Molding Machine Operator

Lans Corporation; Bengaluru; On-site; INR 134,000 - 201,000; Full time

Job summary

Lans Corporation in Bengaluru is seeking an experienced Injection Moulding Operator to run and monitor moulding machines, ensuring smooth production and consistent quality. You will control machine settings, assist with mould changes, and perform basic maintenance while following safety procedures.

The role demands hands-on operation, fault troubleshooting, and meticulous attention to detail to minimize downtime and waste.

Qualifications

• Hands-on experience in Injection Moulding Machine Operation.
• Knowledge of injection moulding processes and machine parameters.
• Basic mould setting and changeover knowledge.

Responsibilities

• Operate injection moulding machines safely and efficiently.
• Set and monitor machine parameters (temperature, pressure, cycle time).
• Assist with mould installation, changeover, and alignment.
• Follow daily production plans and ensure targets are met.
• Inspect finished parts for defects and ensure quality standards.
• Record production data and downtime for shift reporting.
• Maintain clean and organized work area and perform basic maintenance.
• Adhere to safety rules and PPE requirements.

Skills

Machine operation

Quality control

Troubleshooting

Safety compliance

Job description

Role & responsibilities

We are looking for an experienced Injection Moulding Operator to operate and monitor injection moulding machines, ensure smooth production, maintain product quality, and handle routine machine-related activities. The candidate should have hands‑on experience in machine operation, mould setting, process monitoring, troubleshooting, and basic machine maintenance.

Key Responsibilities

1. Machine Operation

• Operate injection moulding machines safely and efficiently.
• Start, stop, and monitor machines during production.
• Set and monitor machine parameters such as temperature, pressure, injection speed, holding pressure, cooling time, and cycle time.
• Ensure machines are running according to approved production parameters.
• Monitor machine performance throughout the production process.

2. Mould Setting & Changeover

• Assist with mould installation, removal, and changeover.
• Ensure proper mould alignment and clamping.
• Connect and check water cooling lines, hydraulic/pneumatic connections, and other required utilities.
• Verify mould condition before starting production.
• Carry out trial runs after mould changes and report abnormalities.

3. Production Process

• Follow daily production plans and achieve assigned production targets.
• Load and handle approved raw materials as per production requirements.
• Monitor material feeding and drying requirements where applicable.
• Maintain proper cycle time and machine efficiency.
• Minimize machine downtime, rejection, and material wastage.

4. Quality Control

• Inspect finished components for defects such as short moulding, flash, sink marks, burn marks, warpage, colour variation, and dimensional issues.
• Follow quality standards and approved samples.
• Segregate defective products and inform the supervisor immediately.
• Maintain consistent product quality throughout production.

5. Troubleshooting

• Identify basic machine and mould-related problems during production.
• Make minor process adjustments within authorized parameters.
• Report machine breakdowns, abnormal noises, temperature issues, hydraulic problems, or mould defects to the maintenance/supervisor team.
• Support troubleshooting and corrective actions to reduce downtime.

6. Machine & Workplace Maintenance

• Perform routine cleaning and basic maintenance of the injection moulding machine and surrounding work area.
• Keep moulds, tools, machines, and production areas clean and organized.
• Check oil levels, cooling systems, heaters, sensors, and other basic operating conditions.
• Follow preventive maintenance schedules as instructed.

7. Safety & Compliance

• Follow all factory safety rules and PPE requirements.
• Ensure safe handling of machines, moulds, raw materials, and tools.
• Follow proper lockout/safety procedures when required.
• Immediately report unsafe conditions, machine abnormalities, or accidents to the supervisor.
• Maintain good housekeeping and follow 5S practices.

8. Production Records & Reporting

• Maintain production records, rejection records, machine downtime, and material usage.
• Record shift‑wise production quantities and defects.
• Report production issues and machine problems to the Production Supervisor.
• Support inventory and material tracking when required.

Preferred candidate profile

• Hands‑on experience in Injection Moulding Machine Operation.
• Knowledge of injection moulding processes and machine parameters.
• Basic knowledge of mould setting and changeover.
• Ability to identify common moulding defects.
• Basic troubleshooting skills.
• Knowledge of raw materials such as PP, ABS, HDPE, PVC, Nylon, etc. is an advantage.
• Ability to read and follow production instructions.
• Good attention to detail and quality awareness.
• Ability to work independently and as part of a production team.
• Good safety awareness.