Dimensional Inspector
NAES Corporation
A complete application in a minute
Tailored resume and cover letter, ready to send.
Job summary
NAES - Houston Office in Spring, TX is seeking a Dimensional Inspector to perform advanced dimensional and visual inspections and ensure components meet drawings, specs, and acceptance criteria.
You will interpret engineering drawings, support NCRs and investigations, and assist less‑experienced inspectors while maintaining calibration and clean work areas. The role offers a competitive salary range and opportunities to contribute to quality improvements at our industrial site.
Qualifications
- High School diploma or equivalent.
- Five years of dimensional inspection, machining, manufacturing, refurbishment, repair, or closely related quality experience.
- Strong written and verbal communication skills.
Responsibilities
- Perform receiving, in‑process, final, first‑piece, and dimensional inspections as assigned.
- Interpret engineering drawings, specifications, work instructions, inspection plans, travelers, and customer requirements.
- Verify dimensional characteristics against applicable tolerances and acceptance criteria.
- Apply working knowledge of Geometric Dimensioning and Tolerancing (GD&T) during inspection activities.
- Perform inspections using appropriate approved inspection methods and available equipment.
- Verify part identification, revision level, material/part traceability, and inspection status.
- Document actual inspection results clearly and accurately on inspection reports, travelers, checklists, or electronic records.
- Identify, document, and segregate nonconforming product when required.
- Initiate or support Nonconformance Reports (NCRs) and provide objective inspection evidence to support disposition.
- Verify reworked or repaired components following completion of corrective work.
- Support First Article Inspection, final acceptance, and customer or third‑party inspection activities when required.
- Review inspection documentation for completeness and accuracy before product release.
- Assist Quality and Engineering with dimensional evaluation of discrepant components.
- Support investigations involving dimensional nonconformities, repeat defects, or inspection escapes.
- Maintain proper handling and care of assigned inspection equipment.
- Verify inspection equipment is within its required calibration status before use.
- Follow established procedures for reporting damaged, questionable, or out‑of‑calibration inspection equipment.
- Support training and mentoring of Level I–III inspectors as requested.
- Communicate quality concerns promptly to Quality, Engineering, Operations, or supervision.
- Maintain a clean and organized inspection/work area.
- Perform other quality‑related duties consistent with the position.
Skills
Education
Tools
Job description
NAES - Houston Office
Spring, TX 77380, USA
About NAES
At NAES, you’ll find engaging and challenging career opportunities in the power generation, renewable energy and industrial construction industry. At every level of the company, we share a common goal: To instill confidence in our clients through our steadfast commitment to safety, integrity and quality of work.
NAES is largest independent operator of power facilities in the industry, operating more than 190 power plants throughout the United States, Canada, Mexico and the UK that span all technologies and provide over 49 GW of capacity. With the strength of 4000 people, our growing family of companies now addresses the entire life cycle of power generation and other industrial plants.
Summary
The Dimensional Inspector is responsible for performing advanced dimensional and visual inspection activities to verify that manufactured, repaired, refurbished, and received components meet applicable drawings, specifications, customer requirements, work instructions, and acceptance criteria.
Work independently, identify nonconforming conditions, accurately document inspection results, support root‑cause investigations, and assist less‑experienced inspectors when needed.
Primary Duties
- Perform receiving, in‑process, final, first‑piece, and dimensional inspections as assigned.
- Interpret engineering drawings, specifications, work instructions, inspection plans, travelers, and customer requirements.
- Verify dimensional characteristics against applicable tolerances and acceptance criteria.
- Apply working knowledge of Geometric Dimensioning and Tolerancing (GD&T) during inspection activities.
- Perform inspections using appropriate approved inspection methods and available equipment.
- Verify part identification, revision level, material/part traceability, and inspection status.
- Document actual inspection results clearly and accurately on inspection reports, travelers, checklists, or electronic records.
- Identify, document, and segregate nonconforming product when required.
- Initiate or support Nonconformance Reports (NCRs) and provide objective inspection evidence to support disposition.
- Verify reworked or repaired components following completion of corrective work.
- Support First Article Inspection, final acceptance, and customer or third‑party inspection activities when required.
- Review inspection documentation for completeness and accuracy before product release.
- Assist Quality and Engineering with dimensional evaluation of discrepant components.
- Support investigations involving dimensional nonconformities, repeat defects, or inspection escapes.
- Maintain proper handling and care of assigned inspection equipment.
- Verify inspection equipment is within its required calibration status before use.
- Follow established procedures for reporting damaged, questionable, or out‑of‑calibration inspection equipment.
- Support training and mentoring of Level I–III inspectors as requested.
- Communicate quality concerns promptly to Quality, Engineering, Operations, or supervision.
- Maintain a clean and organized inspection/work area.
- Perform other quality‑related duties consistent with the position.
Working Relationships
The Dimensional Inspector reports to the Quality Manager and will work with other inspectors.
Compensation
The initial salary range is $76,400 to $87,900 based on experience and qualifications.
Job Qualifications
- Education: High School diploma or equivalent.
- Years of Experience: Five years of dimensional inspection, machining, manufacturing, refurbishment, repair, or closely related quality experience.
- Software/Equipment Knowledge:
- GD&T fundamentals and application
- Calipers, Micrometers, Indicators and Depth and height measuring tools
- Bore gauges, thread gauges, pin gauges, radius or feeler gauges
- Surface plates and related manual inspection tools
- Basic understanding of machining and manufacturing processes
- Other Considerations:
- Able to independently interpret engineering drawings and dimensional requirements.
- Able to determine product conformity based on defined requirements and objective evidence.
- Strong written and verbal communication skills.
- Able to accurately complete inspection records and quality documentation.
- Able to identify and communicate nonconforming conditions.
- Strong attention to detail and organizational skills.
- Able to work independently with limited supervision.
- Dimensional tolerances
- Inspection planning and documentation
- Product identification and traceability
- Nonconformance identification and control
- Problem‑solving and sound inspection judgment
- Able to distinguish between specification requirements and personal preference
Core Competencies:
- Perform complex dimensional inspections independently.
- Exercise sound judgment within established inspection authority.
- Recognize when Engineering or Quality disposition is required rather than making unauthorized technical decisions.
- Assist with difficult dimensional evaluations and inspection planning.
- Serve as a technical resource for less experienced inspectors.
- Support customer, supplier, and third‑party inspections when requested.
- Identify recurring inspection or manufacturing issues and communicate opportunities for improvement.
- Maintain accurate, defensible objective evidence supporting product acceptance or rejection
Physical Requirements and Working Conditions
Normal working hours are 8:00a.m. to 5:00p.m. Monday through Friday. Extended hours may be required based on specific project requirements. Ability to travel up to 15% is required. Work is performed at an established industrial site that requires protective clothing and equipment, which NAES will pay for. Work at facilities can occur around industrial hazards, in areas of high noise levels, and around new construction. Ability to stand, walk, bend, and work around manufacturing or refurbishment equipment for extended periods. Ability to safely handle inspection equipment and components appropriate to the assigned work. Ability to visually inspect components and read drawings, specifications, and inspection documentation. Physical mobility to transverse stairways, ladders, grating, and uneven terrain are essential. Ability to see, hear, read, and react to warning signs, lights, and alarms are essential.
Fit for Duty
All employees will participate in the Fitness for Duty Program. This program includes a post‑offer physical examination and drug screening and post‑employment random drug screening. There are extensive smoking restrictions in and around the facility.
NAES Safe
Safety is a core value of NAES and as a condition of employment, all employees are expected to be mentally alert and work safely at all times. Additionally, employees are required to adhere to all safety warnings and posted safety signs whenever on company property. Furthermore, employees must follow all NAES safety rules and procedures. Effectiveness in carrying out this responsibility is part of the evaluation of each employee’s performance.
NAES is committed to a diverse and inclusive workplace. It is the practice of NAES to seek employees of the highest quality and to select individuals on the basis of merit and competence, without regard to race, color, religion, national origin, gender, gender identity, sexual orientation, age, disability, military status or affiliation protected under USERRA, or any other basis of discrimination prohibited by applicable local, state and federal law.
Intermediate
Intermediate
Intermediate
Intermediate
Intermediate
Intermediate
Capable of carrying out a given task with all details necessary to get the task done well
Shows intense and eager enjoyment and interest
Consistently introduces new ideas and demonstrates original thinking
Works well as a member of a group
High School or better.
5 years:Dimensional inspection, machining, manufacturing, refurbishment, repair, or closely related quality experience.
Able to independently interpret engineering drawings and dimensional requirements.
Able to determine product conformity based on defined requirements and objective evidence.
Driver's License
Equal Opportunity Employer
This employer is required to notify all applicants of their rights pursuant to federal employment laws.For further information, please review the Know Your Rights notice from the Department of Labor.
'/%3e%3cpath%20d='M101.744%2012.4726L102.894%2016.1947L99.0021%2013.2201L101.744%2012.4726ZM105.3%208.40937H100.488L99.0026%203.59473L97.5116%208.41047L92.7%208.40385L96.5965%2011.3834L95.1055%2016.1942L99.0021%2013.2196L101.408%2011.3834L105.3%208.40992V8.40937Z'%20fill='white'/%3e%3cdefs%3e%3clinearGradient%20id='paint0_linear_5593_1381'%20x1='90'%20y1='9.44471'%20x2='99'%20y2='9.44471'%20gradientUnits='userSpaceOnUse'%3e%3cstop%20stop-color='%2300AD70'/%3e%3cstop%20offset='0.998594'%20stop-color='%2300B67A'/%3e%3cstop%20offset='1'%20stop-color='%23DCDCE6'/%3e%3c/linearGradient%3e%3c/defs%3e%3c/svg%3e){kind=small}
