Assembly (Mechanical) - 2nd Shift

Maxcess International; Keene (NH); On-site; USD 34,000 - 52,000; Full time

Job summary

Maxcess International is seeking an Assembler in Keene, NH to join the Assembly Department. The role focuses on cutting, straightening, pre-assembling and assembling shafts and accessories, and final inspection.

Candidates must follow safety and manufacturing policies and be flexible to assist in other areas as needed. The position requires manual dexterity, adherence to engineering prints, and meticulous inspection of finished parts.

Responsibilities

• Polish, roll stamp and deburr bodies.
• Prep bodies for assembly including cleaning ID of body, removal of burrs on ID of body.
• Straighten internal leaves/lugs, splitting and finishing ends as required.
• Prep journals for assembly by cleaning out tube socket and air hole. Install connector and valve.
• Obtain pre-packed parts from holding area and verify correct part numbers as identified on material list.
• Drill and tap side valve according to engineering prints and established procedures.
• Drill and tap set screws according to engineering prints following established procedures.
• Assemble shafts according to engineering prints following established procedures.
• Install accessory parts listed on Material List/Inspection Report (i.e. pins, bearing races, and drive ends).
• Assemble bearing housings according to print and procedure.
• Hand stamp as required.
• Final inspection of products to verify dimensions, function, quality and appearance.
• Fill out required inspection reports, accepted stickers, and quality audit reports.
• Inform supervision of any non-conformities found during inspection.
• Install serial number tags as required.
• Disassemble and inspect repair product completing required inspection form.
• Perform repairs on product according to Sales Order.
• Move completed product work to proper holding area with identifying paperwork according to established procedures.
• Maintain neat and clean working area. Notify supervisor of any equipment defects.
• Maintain and record time sheets for each operations performed.
• Wear and maintain proper safety equipment including proper footwear, safety glasses, and hearing protection where required.
• Assist in other areas of manufacturing as required.
• Work in a safe manner at all times following established policies and procedures.

Job description

The Assembly Department is a part of the Keene manufacturing team whose primary responsibility is the cutting, straightening, pre-assembling and assembling of shafts and accessories, as well as final inspection. The Assembler is a highly skilled manual role requiring attention to detail, critical thinking and adherence to assembly drawings. As with all other roles within Tidland Keene, this individual must adhere to all documented safety and manufacturing policies and procedures, as well as be flexible enough to assist in other areas as business needs dictate.

SPECIFIC RESPONSIBILITIES

• Polish, roll stamp and deburr bodies.
• Prep bodies for assembly including cleaning ID of body, removal of burrs on ID of body.
• Straighten internal leaves/lugs, splitting and finishing ends as required.
• Prep journals for assembly by cleaning out tube socket and air hole. Install connector and valve.
• Obtain pre-packed parts from holding area and verify correct part numbers as identified on material list.
• Drill and tap side valve according to engineering prints and established procedures.
• Drill and tap set screws according to engineering prints following established procedures.
• Assemble shafts according to engineering prints following established procedures.
• Install accessory parts listed on Material List/Inspection Report (i.e. pins, bearing races, and drive ends).
• Assemble bearing housings according to print and procedure.
• Hand stamp as required.
• Final inspection of products to verify dimensions, function, quality and appearance.
• Fill out required inspection reports, accepted stickers, and quality audit reports.
• Inform supervision of any non-conformities found during inspection.
• Install serial number tags as required.
• Disassemble and inspect repair product completing required inspection form.
• Perform repairs on product according to Sales Order.
• Move completed product work to proper holding area with identifying paperwork according to established procedures.
• Maintain neat and clean working area. Notify supervisor of any equipment defects.
• Maintain and record time sheets for each operations performed.
• Wear and maintain proper safety equipment including proper footwear, safety glasses, and hearing protection where required.
• Assist in other areas of manufacturing as required.
• Work in a safe manner at all times following established policies and procedures.

Maxcess is an equal employment opportunity employer. We do not discriminate on the basis of race, religion, sex, disability, age, pregnancy, national origin, sexual orientation, or any other characteristic protected by applicable law. We are committed to diversity and inclusion, and all qualified candidates are encouraged to apply.

As set forth in Maxcess International’s Equal Employment Opportunity policy,we do not discriminate on the basis of any protected group status under any applicable law.

Voluntary Self-Identification

For government reporting purposes, we ask candidates to respond to the below self-identification survey.Completion of the form is entirely voluntary. Whatever your decision, it will not be considered in the hiringprocess or thereafter. Any information that you do provide will be recorded and maintained in aconfidential file.

As set forth in Maxcess International’s Equal Employment Opportunity policy,we do not discriminate on the basis of any protected group status under any applicable law.

If you believe you belong to any of the categories of protected veterans listed below, please indicate by making the appropriate selection.As a government contractor subject to the Vietnam Era Veterans Readjustment Assistance Act (VEVRAA), we request this information in order to measurethe effectiveness of the outreach and positive recruitment efforts we undertake pursuant to VEVRAA. Classification of protected categoriesis as follows:

A "disabled veteran" is one of the following: a veteran of the U.S. military, ground, naval or air service who is entitled to compensation (or who but for the receipt of military retired pay would be entitled to compensation) under laws administered by the Secretary of Veterans Affairs; or a person who was discharged or released from active duty because of a service-connected disability.

A "recently separated veteran" means any veteran during the three-year period beginning on the date of such veteran's discharge or release from active duty in the U.S. military, ground, naval, or air service.

An "active duty wartime or campaign badge veteran" means a veteran who served on active duty in the U.S. military, ground, naval or air service during a war, or in a campaign or expedition for which a campaign badge has been authorized under the laws administered by the Department of Defense.

An "Armed forces service medal veteran" means a veteran who, while serving on active duty in the U.S. military, ground, naval or air service, participated in a United States military operation for which an Armed Forces service medal was awarded pursuant to Executive Order 12985.