Lead PCB Design Engineer

EMTensor GmbH; Wien; Vor Ort; EUR 70.000 - 100.000; Vollzeit

Zusammenfassung

EMTensor GmbH in Vienna, Austria, is seeking an experienced PCB layout engineer to own the layout of an eight-layer mixed-signal board for our microwave tomography instrument. You will take the board from placement to a released fabrication package and stay with it through the first build.

You will work directly with the schematic engineer, FPGA engineer and system architect, with no project-management layer between you and design decisions.

Qualifikationen

• Eight or more years of board-level PCB layout experience.
• Real RF layout experience with antenna ports, RF traces, matching and shielding.
• Proficient in Altium Designer; quick tool-switch acceptable.
• Experience with stack-up, controlled impedance, microstrip and coplanar waveguide.
• Fluency in Gerbers, drill data, DFM and manufacturing packaging.

Aufgaben

• Own the PCB layout for eight-layer mixed-signal boards from placement to fabrication package.
• Collaborate directly with schematic, FPGA, and system architect engineers.
• RF routing and impedance control throughout the design.
• Validate designs with fabricator discussions and first-article acceptance.

Kenntnisse

RF layout

PCB layout

Altium Designer

Eight+ years

High-speed routing

Jobbeschreibung

EMTensor develops electromagnetic (microwave) tomography systems for brain imaging — scanners that detect and monitor stroke at the bedside and in the ambulance. We are headquartered in Vienna, Austria, with an engineering office in Bengaluru, India. The team is small, so the engineer who designs something owns it end to end.

The Role

You own PCB layout for our instrument hardware: an eight-layer mixed-signal board carrying an analogue front end, an RF chain around 1 GHz and a data-conversion stage. You take the board from placement to a released fabrication package, and you stay with it through the first build.

You work directly with the schematic engineer, the FPGA engineer and the system architect. There is no layer of project management between you and the design decisions.

What You Will Work On

Placement, stack-up and material selection to meet impedance targets on an eight-layer board.

RF routing: impedance-controlled traces, matching networks, ground pours and return paths, shielding, connector transitions.

High-speed routing: differential pairs, length and topology matching, reference continuity, EMC.

A demanding drill specification — 1,060 holes of Ø0.15 mm through 1.61 mm, an aspect ratio of 10.7:1. You will discuss this with the fabricator and decide what is buildable.

Gerbers, drill data, DFM and DFA checks, answering fabricator queries, first-article acceptance.

Feeding layout constraints back into the schematic — telling us early when a part choice will not route.

What We Are Looking For

Eight or more years of board-level PCB layout.

Real RF layout experience — boards where the RF section was yours. This is the requirement we will not compromise on. Antenna ports, RF traces, matching, shielding: we will ask you what you routed and how you verified it.

Altium Designer. If your main tool has been Allegro, Xpedition, PADS or OrCAD, tell us — we will ask how quickly you can switch, and a good answer is enough.

Stack-up, controlled impedance, microstrip and coplanar waveguide, differential pairs, via strategy.

Fluency with the manufacturing package: Gerbers, drill files, DFM, and working with fabricators and assemblers.

Nice to Have

Signal- and power-integrity simulation (HyperLynx or equivalent), IR-drop analysis.

IPC-CID or CID+ certification.

A background in radar, instrumentation, scientific equipment, defence, space or wireless products.

Experience mentoring or leading other layout engineers.

A Note on Scope

This is board-level PCB layout. It is not IC, analogue or mask layout — if your work has been inside the chip rather than on the board, this is not the right role. Schematic design is handled by a separate engineer on the same team; we are hiring for that position in parallel.

We read every application ourselves and reply to each one. If your CV lists tools without projects, add a few lines about one board you worked on — that is what we look at first.