Touch Up/Rework Operator (Second Shift)

Rocket-Ems; Santa Clara (CA); On-site; USD 35,817 - 41,328; Full time

Job summary

Rocket EMS is seeking a Touch-Up / Rework Technician to diagnose, repair, and rework PCBAs and mechanical assemblies. Strong soldering skills, documentation interpretation, and precision repair using hand tools and equipment are essential.

You will collaborate with Manufacturing, Test, Quality, and Engineering teams to ensure workmanship and IPC compliance, while maintaining ESD protocols in a manufacturing environment. Pay range shown below.

Qualifications

• Experience performing soldering and rework on electronic assemblies.
• Ability to work under microscope for fine-pitch components.
• Familiarity with SMT and through-hole component repair.
• Ability to read and interpret assembly documentation and engineering drawings.
• Knowledge of ESD handling practices.
• Strong attention to detail and manual dexterity.
• Ability to work independently and follow repair procedures.

Responsibilities

• Perform component-level rework and touch-up on PCBAs including SMT and through-hole components.
• Remove and replace electronic components using soldering irons, hot air rework stations, and other repair tools.
• Repair lifted pads, damaged traces, solder bridges, and other workmanship defects.
• Perform wire modifications, jumpers, and engineering changes per documentation.
• Interpret assembly drawings, schematics, BOMs, and work instructions.
• Use microscopes and inspection equipment to identify defects and verify repair quality.
• Conduct mechanical rework and assembly repairs including hardware replacement and structural corrections.
• Document rework activity in manufacturing systems or travelers.
• Support debug and test teams by troubleshooting assembly failures when required.
• Maintain ESD compliance and proper handling of sensitive electronics.
• Ensure repaired products meet IPC workmanship standards and internal quality requirements.

Skills

Soldering

Microscope inspection

Reading assembly docs

ESD handling

Attention to detail

Manual dexterity

Independent work

Tools

Soldering irons

Hot air rework station

Microscopes

Inspection equipment

Job description

The Touch-Up / Rework Technician is responsible for diagnosing, repairing, and reworking printed circuit board assemblies (PCBAs) and mechanical assemblies that do not meet quality standards. This position requires strong soldering skills, the ability to interpret engineering documentation, and experience performing precision repairs on electronic assemblies using hand tools and specialized equipment.

The technician will work closely with Manufacturing, Test, Quality, and Engineering teams to ensure products meet workmanship standards, IPC requirements, and customer specifications.

Essential Duties and Responsibilities

• Perform component-level rework and touch-up on PCBAs including SMT and through-hole components


• Remove and replace electronic components using soldering irons, hot air rework stations, and other repair tools


• Repair lifted pads, damaged traces, solder bridges, and other workmanship defects


• Perform wire modifications, jumpers, and engineering changes per documentation


• Interpret assembly drawings, schematics, BOMs, and work instructions


• Use microscopes and inspection equipment to identify defects and verify repair quality


• Conduct mechanical rework and assembly repairs including hardware replacement and structural corrections


• Document rework activity in manufacturing systems or travelers


• Support debug and test teams by troubleshooting assembly failures when required


• Maintain ESD compliance and proper handling of sensitive electronics


• Ensure repaired products meet IPC workmanship standards and internal quality requirements

Required Skills and Qualifications

• Experience performing soldering and rework on electronic assemblies


• Ability to work under microscope for fine-pitch components


• Familiarity with SMT and through-hole component repair


• Ability to read and interpret assembly documentation and engineering drawings


• Knowledge of ESD handling practices


• Strong attention to detail and manual dexterity


• Ability to work independently and follow structured repair procedures

Preferred Qualifications

• IPC‑A‑610 or IPC‑7711/7721


• Experience with BGA/QFN component rework


• Prior work in electronics manufacturing or contract manufacturing


• Experience supporting failure analysis or debug teams

Physical Requirements

• Ability to sit or stand for extended periods


• Ability to work under magnification for detailed work


• Ability to lift up to 25 lbs occasionally

This position operates in a manufacturing environment handling electronic assemblies and requires adherence to ESD and safety protocols.

Pay Range

$26 - $30 USD

Rocket EMS will consider qualified applicants with criminal histories in a manner consistent with the California Fair Chance Act. Candidates are not required to disclose criminal history or participate in a background check unless and until a conditional offer of employment has been made. Any final offer of employment may be conditioned on completion of a background check, consistent with applicable law.