Mechanical Inspector in San Fernando

Energy Jobline ZR; San Fernando (CA); On-site; USD 65,000 - 90,000; Full time

Job summary

Aerospace Products in California seeks a skilled inspector to verify dimensions on incoming hardware using CMM software, prints, and inspection plans. You will work from approved documents and use precision instruments to confirm tolerances and surface finishes.

The role requires 3–5 years of aerospace inspection experience, GD&T proficiency, and the ability to read blueprints, generate NCRs, and maintain calibration logs in a fast-paced production environment.

Qualifications

• Minimum 3-5 years’ experience with the inspection of aircraft components.
• Must be able to inspect all of the above mentioned dimensions.
• Competence to read and interpret documents such as safety policies, operating and maintenance instructions, and procedure manuals
• Ability to write routine reports and correspondence
• Ability to effectively communicate with individuals and groups within the organization
• Ability to perform basic arithmetic and unit conversions
• Knowledge of AS9100 requirements is a plus

Responsibilities

• Inspect incoming hardware from approved inspection plans and drawings.
• Verify dimensions, angles, radii, contours, holes and surface finishes.
• Maintain calibration logs and document non-conformances.
• Sign off steps on routers and follow inspection procedures.
• Generate RMA, NCR, and CAR as needed.

Skills

Dimensional measurement

Reading drawings/BDTs

GD&T knowledge

Written reports

Communication

Mathematical proficiency

Calibration knowledge

Tools

CMM

Sine plate

Comparators

Profile-meter

Height gauge

Surface plate

Caliper

Micrometer

Job description

Job DescriptionJob Description

Essential Job Functions:

Inspect incoming hardware utilizing CMM software and prints/ Cad Models / inspection plans. Work from approved inspection plans, engineering drawings, purchase orders, operation sheets and specifications. Use a variety of precision measuring instruments to verify compliance on dimensions, angles, radii, contours, holes, surface finishes, concentricity, hardness, material and plating.

• Checks parts visually for burrs, finish, and any related defects that would be cause for the rejection of parts
• Use a wide variety of precision measuring instruments to verify compliance on: dimensions, angles, radii, contours, holes, surface finish, concentricity, hardness, plating, etc.
• Should be proficient with sine plate, comparators, profile-meter and surface plate layout using height gages.
• Work involves simple to complex setups on surface plates using height gauge, gauge blocks, sine plates and indicators.
• Maintain daily logs and initiate non-conforming documentation for parts not meeting requirements.

Required Skills:

• Minimum 3-5 years’ experience with the inspection of aircraft components.
• Generating RMA, NCR, and CAR
• Must be able to inspect all of the above mentioned dimensions.
• Competence to read and interpret documents such as safety policies, operating and maintenance instructions, and procedure manuals
• Ability to write routine reports and correspondence
• Ability to effectively speak after individuals and groups of employees within the organization
• Ability to add, subtract, multiply, and divide in units of measure, using whole numbers, common fractions, and decimals
• Ability to apply common sense understanding to carry out simple one or two step instructions
• Basic knowledge of AS9100 requirements
• May have to perform calibration on gages needed for production
• Utilizes shop math in all dimensional checking as well as precision measuring devices.
• Experience interpreting & inspecting GD&T features ()
• Experience working in an aerospace company
• Experience working with a CMM
• Follows inspection procedure for each inspection.
• Follows all procedures such as signing off each step on the router.
• Keeping up with calibration log and calibrating employees’ and CIM inspection equipment
• High knowledge of inspection equipment (Caliper, Micrometer, Height gauge, Optical Comparator and CMM).
• Demonstrated expertise in Geometric Dimensioning and Tolerance (GD&T).
• Proficient in operating CMMs
• Solid technical knowledge and hands-on experience with measurement tools and equipment.

We are an Equal Employment Opportunity Employer.

Company Description

Aerospace Products has over 50 years of manufacturing experience. They are dedicated to the design, development, manufacture and marketing of high quality products and services. Aerospace Products are selected by major aerospace, transportation and industrial equipment manufactures.

Company DescriptionAerospace Products has over 50 years of manufacturing experience. They are dedicated to the design, development, manufacture and marketing of high quality products and services. Aerospace Products are selected by major aerospace, transportation and industrial equipment manufactures.