Global Metrology Engineer

Technimark; North Carolina; On-site; USD 85,000 - 110,000; Full time

Job summary

Technimark in North Carolina seeks a metrology engineer with a 4-year science/engineering degree or equivalent experience. You will apply advanced metrology techniques, develop measurement plans, and support SPC data analysis.

Responsibilities include translating customer requirements into TM specs, validating test methods, and performing GD&T-based analyses. Strong communication and documentation skills are essential; experience with PC-DMIS, Calypso, and PolyWorks is highly valued.

Qualifications

• Requires 4-year degree in science, math, or engineering or equivalent experience.
• 2 years of metrology engineering experience preferred.
• Ability to develop procedures and write technical reports.
• Strong communication, data analysis, and SPC skills.
• Knowledge of GD&T and metrology techniques.

Responsibilities

• Interface with customers to define requirements and translate to TM specs.
• Support development of metrology methods and validation plans.
• Develop measurement procedures and work instructions.
• Assist data acquisition, online reporting, and SPC initiatives.
• Investigate root causes and contribute to corrective actions.
• Review drawings and perform critical dimension analyses.
• Translate blueprints into measurement strategies using CMMs and gages.

Skills

Statistical analysis

Gage R&R

GD&T understanding

Test method validation

Metrology techniques

Python scripting

3D measurement planning

Data trending/SPC

Education

Bachelor's degree in science/engineering

Tools

PC-DMIS

Calypso

Zone 3 offline

WinWerth

Geomagic Control X

GOM Volume Inspect

PolyWorks

Job description

4-year degree in science, math, or engineering with 2 years of experience in metrology engineering preferred. Relevant experience and demonstrated skills in advanced metrology will be considered in lieu of a 4-year degree. Ability to develop written procedures and perform technical report writing required. Good communication and interpersonal skills required. Must be proficient in statistical data analysis and test plan development. Must be proficient in measurement system analysis and test method validation techniques and possess understanding of metrology techniques. Basic understanding of GD&T and Solid Modeling required. Ability to design or technically describe for design of fixtures required for metrology is required. A general knowledge of quality systems, ISO standards, and measurement equipment calibration techniques is necessary. Experience in metrology equipment programming is required. Training in advanced metrology techniques including any programming experience in PCDMIS, Calypso, Zone 3 offline, WinWerth, Geomagic Control X, GOM Volume Inspect or PolyWorks from 3D models preferred. Experience with Python or similar scripting is highly desirable. Working knowledge of Datum Reference System, 6 DoF or familiar with Analytic Geometries in 3D. Scanning equipment (surface or volumetric) familiarity is preferred.

• Interfaces with internal and external customers to define, interpret, and understand customer requirements and specifications.
• Translates the customer requirements into TM specifications for new product development in conjunction with customer engineering.
• Supports development of test methods and test method validation plans.
• Supports development of metrology techniques and standards for inspection procedures including work instructions for execution.
• Supports shop floor data acquisition, tracking and trending of data, and SPC initiatives globally.
• Supports complaint investigation, root cause analysis and implementation of corrective actions along with continuous improvement activities.
• Supports and executes product drawing reviews and critical dimension analyses.
• Effectively translates blueprints or drawings into measurement strategies using a variety of measurement tools including Optical and Touch Probe CMMs, Optical Comparators, manual gages and precision measuring instruments.
• Defines and executes measurement analyses including repeatability, reproducibility, multivariate Gage R&R, Measurement Tool Correlation, etc.
• Executes metrology tasks with requirements from ISO 10360, ISO 17025, and ASME GD&T 14.5 as necessary.
• Globally supports data acquisition and reporting programs for metrology.

Technimark is an Equal Opportunity Employer and will consider all qualified applicants for employment without regard to race, color, religion, gender, sexual orientation, gender identity, national origin, age, disability, or protected veteran status.

Equal Opportunity Employer
This employer is required to notify all applicants of their rights pursuant to federal employment laws.For further information, please review the Know Your Rights notice from the Department of Labor.