Cobalt TN Repair Technician

MBI; Lenoir City (TN); On-site; USD 21,000 - 34,000; Full time

Job summary

MBI in Cobalt, TN is seeking a Detail Technician to repair hulls and decks to Cobalt standards while following safety protocols.

The role involves removing damaged gel coat, sanding, buffing, repainting, and inspecting parts; strong attention to quality and teamwork required.

Qualifications

• High school diploma or GED or 1–3 months related experience.
• Ability to read and interpret documented procedures.
• Basic Math skills.
• Ability to recognize and solve problems on the go.
• Reasonable accommodations may be made to enable individuals with disabilities to perform the essential functions.

Responsibilities

• Wipe down, buff, and inspect each part to identify flaws or damage.
• Sand and buff problem area to create a smooth, shiny surface.
• Cut flaws out of fiberglass and fill holes with gel coat mixture.
• Paint over thin or damaged gel coat areas to create a flawless surface.
• Correct crooked paint lines to create straight lines.
• Repair major hull or deck areas to fix errors from cutting.
• Inspect, repair, and finesse the boat at end of the line.
• Other duties may be assigned.

Skills

Verbal comprehension

Reading procedures

Basic Math

Education

High school diploma or GED

Job description

Job Details

Job Location: Cobalt TN - Lenoir, TN 37771

Job Title: Detail Technician

Department: Detail

Reports To: Department Supervisor

FLSA Status: Hourly

Summary

Repair of hulls and/or decks to Cobalt standards while following safety protocols.

Essential Duties and Responsibilities

• Wipe down, buff, and inspect each part to identify flows or damage. Done by manually wiping part off using towel and acetone, buffing the part (removing wax and wiping off compound), visually identifying and marking flaw with grease pencil.
• Sand and buff problem area to make a smooth, shiny surface. Done by sanding manually or with power sander, then buffing with air powered buffer until smooth.
• Cut flaws out of fiberglass to remove problem area by using router or razor blade. Then mix gel coat and catalyst filling in hole with mixture using tongue depressor.
• Paint over thin or damaged areas of gel coat to create flawless surface.
• Correct crooked paint lines to create straight paint lines.
• Repair major areas in hull or deck to correct errors made while cutting.
• Repairing areas that are damaged during assembly.
• Inspecting, repairing, and finessing boat at the end of the line.
• Other duties may be assigned.

Qualifications

QualificationsQualifications To perform this job successfully, an individual must be able to perform each essential duty satisfactorily. The requirements listed below are representative of the knowledge, skill, and/or ability required. Reasonable accommodations may be made to enable individuals with disabilities to perform the essential functions.

Education and/or Experience

High school diploma or general degree (GED); or one to three months related experience and/or training; or equivalent combination of education and experience.

Language Skills

Verbal instruction & comprehension are key in this role. Ability to read and interpret documented procedures.

Mathematical Skills

Basic Math

Reasoning Ability

Ability to recognize and solve problems on the go.

Physical Demands

The physical demands described here are representative of those that must be met by an employee to successfully perform the essential functions of this job. Reasonable accommodations may be made to enable individuals with disabilities to perform the essential functions.

Use the drop-down boxes to select the appropriate response to each area.

Continuous/C = 67-100%, Frequent/F = 33-66%, Occasional/O = 33%, None/N

a. Sits 1 hours

b. Stands 4 hours

c. Walks 4 hours

d. Drives 1 hours

Employee Lifts and/or Carries

Maximum: 75 (lbs) Frequently: 25 (lbs) Occasionally: 50 (lbs)

Employee uses Hands for repetitive activities

• a. Simple Grasping: Right, Frequent Left, Frequent
• b. Pushing/Pulling: Right, Frequent Left, Frequent
• c. Fine Manipulation: Right, Frequent Left, Frequent

Employee uses Feet for repetitive activities

• a. Right: Frequent Left: Frequent

Employee is required to perform these activities

• a. Bending At Waist: Frequent
• b. Squatting: Frequent
• c. Climbing Ladders, Stairs: Frequent
• d. Kneeling On Ground: Frequent
• e. Reaching Above Shoulder: Frequent

Work Environment

The work environment characteristics described here are representative of those an employee encounters while performing the essential functions of this job (i.e., heat/cold, dust/dampness, height; chemical; noise) PPE requirements are included. Reasonable accommodations may be made to enable individuals with disabilities to perform the essential functions.

Safety glasses and closed toe shoes required when on production floor. Chemical resistant gloves.

Exposed to all weather conditions. Typical 10-hour workday with overtime without notice.

Competencies

To perform the job successfully, an individual should demonstrate the following competencies:

• Teamwork: Balances team and individual responsibilities; Exhibits objectivity and openness to others' views; Gives and welcomes feedback; Contributes to building a positive team spirit; Puts success of team above own interests; Supports everyone's efforts to succeed.
• Motivation: Measures self against standard of excellence.
• Quality: Demonstrates accuracy and thoroughness; Applies feedback to improve performance; Monitors own work to ensure quality.
• Attendance/Punctuality: Is consistently at work and on time.
• Dependability: Takes responsibility for own actions.