Cobalt Boats Lamination Technician

MBI; Lenoir City (TN); On-site; USD 22,000 - 33,000; Full time

Benefits offered by this job

Safety glasses provided

Chemical resistant gloves

Overtime opportunities

Job summary

MBI in Cobalt, TN is seeking a Lamination Technician to apply fiberglass and resin to gel-coated molds in the Lamination Department. You will follow safety procedures and work with hand tools to ensure quality laminates.

Responsibilities include prep, material selection, cutting, thickness checks, and catalyst mixing, with overtime opportunities on 10-hour shifts.

Qualifications

• High School diploma or GED; or 1–3 months related experience or training.
• Ability to read and comprehend simple instructions.
• General math skills required.
• Ability to apply common sense understanding to carry out instructions.
• Stand for long periods; lift up to 20 pounds.

Responsibilities

• Move parts into position into the Lamination Department.
• Prep parts in accordance with Cobalt standards.
• Select appropriate fiberglass material according to part model. Roll out laminate eliminating air bubbles using specific hand tools, rollers, etc.
• Trim excess material from mold using cutting tool.
• Mix catalyst into resin using proper handling procedures.
• Cut fiberglass mat from spool as needed using scissors.
• Use mill gage to accurately determine material thickness.
• Other duties may be assigned.

Skills

Reading Comprehension

Math Skills

Teamwork

Attention to Detail

Education

High School Diploma or GED

Job description

Job Details

Job Location: Cobalt TN - Lenoir, TN 37771

Job Title: Lamination Technician

Department: Lamination

Reports To: Department Supervisor

FLSA Status: Hourly

Summary

Applies fiberglass and resin to gel coated molds by performing the following duties

Essential Duties and Responsibilities

• Move parts into position into the Lamination Department.
• Prep parts in accordance with Cobalt standards.
• Select appropriate fiberglass material according to part model. Roll out laminate eliminating air bubbles using specific hand tools, rollers, etc.
• Trim excess material from mold using cutting tool.
• Mix catalyst into resin using proper handling procedures.
• Cut fiberglass mat from spool as needed using scissors.
• Use mill gage to accurately determine material thickness.
• Other duties may be assigned.

Qualifications

Qualifications To perform this job successfully, on individual must be able to perform each essential duty satisfactorily. The requirements listed below are representative of the knowledge, skill and/or ability required. Reasonable accommodations may be made to enable individuals with disabilities to perform the essential functions.

Education and/or Experience

High School diploma or general education degree (GED); or one to three months related experience and/or training; or equivalent combination of education and experience.

Language Skills

Ability to read and comprehend simple instructions.

Mathematical Skills

General math skills required.

Reasoning Ability

Ability to apply common sense understanding to carry out detailed but uninvolved written or oral instructions. Ability to deal with problems involving a few concrete variables in standardized situations.

Physical Demands

Must be able to stand for long periods of time. Pull material from rack. Lift up to 20 pounds.

Use the drop down boxes to select the appropriate response to each area. Continuous/C = 67-100%, Frequent/F = 33-66%, Occasional/O = 33%, None/N

• a. Sits 0 hours
• b. Stands 9 hours
• c. Walks 1 hours
• d. Drives 0 hours

Employee Lifts and/or Carries

type amount of weight in each area

• Maximum: 50(lbs) Frequently: 10-20 (lbs) Occasionally: 50 (lbs)

Employee uses Hands for repetitive activities

• a. Simple Grasping: Right, Constant Left, Occasional
• b. Pushing/Pulling: Right, Frequent Left, Frequent
• c. Fine Manipulation: Right, Occasional Left, Occasional

Employee uses Feet for repetitive activities

• a. Right: None Left: None

Employee is required to perform these activities

• a. Bending At Waist: Frequent
• b. Squatting: Occasional
• c. Climbing Ladders, Stairs: Occasional
• d. Kneeling On Ground: Occasional
• e. Reaching Above Shoulder: Occasional

Work Environment

The work environment characteristics described here are representative of those an employee encounters while performing the essential functions of this job (ie; heat/cold, dust/dampness, height; chemical; noise) PPE requirements are included. Reasonable accommodations may be made to enable individuals with disabilities to perform the essential functions.

Safety glasses always required

Chemical resistant gloves required when handling chemicals

Typical 10-hour workdays, frequent overtime required.

Annual Pulmonary Function Testing – Medical Clearance to wear a Respirator Annual Fit Testing – Testing of the Respirator to ensure it fits safety and securely.

Competencies:

• Teamwork: Balances team and individual responsibilities; Exhibits objectivity and openness to others' views; Gives and welcomes feedback; Contributes to building a positive team spirit; Puts success of team above own interests; Supports everyone's efforts to succeed.
• Motivation: Measures self against standard of excellence.
• Quality: Demonstrates accuracy and thoroughness; Applies feedback to improve performance; Monitors own work to ensure quality.
• Attendance/Punctuality: Is consistently at work and on time.
• Dependability: Takes responsibility for own actions.