Cobalt Boats Lamination Technician

Cobalt Boats, LLC; Lenoir City (TN); On-site; USD 34,000 - 52,000; Full time

Job summary

Cobalt Boats, LLC is seeking a Lamination Technician in Lenoir, TN. You will apply fiberglass and resin to gel-coated molds, prep parts, and select materials to ensure quality in the Lamination Department.

The role involves cutting, trimming, and sanding as well as handling catalysts, with safety PPE and manual dexterity emphasized. Typical 10-hour days with overtime are expected.

Qualifications

• Requires ability to perform essential duties satisfactorily.
• Must read and comprehend simple instructions.
• General math and reasoning skills required.

Responsibilities

• Move parts into position in the Lamination Department.
• Prep parts per Cobalt standards.
• Select fiberglass material according to part model; roll laminate to remove air bubbles.
• Trim excess material from mold with cutting tool.
• Mix catalyst into resin following proper procedures.

Skills

Teamwork

Attention to detail

Quality focus

Punctuality

Dependability

Education

High School diploma or GED

Tools

Mill gauge

Hand tools

Fiberglass handling tools

Job description

Job Details

Job Location: Cobalt TN - Lenoir, TN 37771

Job Title: Lamination Technician

Department: Lamination

Reports To: Department Supervisor

FLSA Status: Hourly

Summary: Applies fiberglass and resin to gel coated molds by performing the following duties

Essential Duties and Responsibilities

• Move parts into position into the Lamination Department.
• Prep parts in accordance with Cobalt standards.
• Select appropriate fiberglass material according to part model. Roll out laminate eliminating air bubbles using specific hand tools, rollers, etc.
• Trim excess material from mold using cutting tool.
• Mix catalyst into resin using proper handling procedures.
• Cut fiberglass mat from spool as needed using scissors.
• Use mill gage to accurately determine material thickness.
• Other duties may be assigned.

Qualifications

QualificationsQualifications To perform this job successfully, on individual must be able to perform each essential duty satisfactorily. The requirements listed below are representative of the knowledge, skill and/or ability required. Reasonable accommodations may be made to enable individuals with disabilities to perform the essential functions.

Education and/or Experience

High School diploma or general education degree (GED); or one to three months related experience and/or training; or equivalent combination of education and experience.

Language Skills

Ability to read and comprehend simple instructions.

Mathematical Skills

General math skills required.

Reasoning Ability

Ability to apply common sense understanding to carry out detailed but uninvolved written or oral instructions. Ability to deal with problems involving a few concrete variables in standardized situations.

Physical Demands

Use the drop down boxes to select the appropriate response to each area. Continuous/C = 67-100%, Frequent/F = 33-66%, Occasional/O = 33%, None/N

• a. Sits 0 hours
• b. Stands 9 hours
• c. Walks 1 hours
• d. Drives 0 hours

Employee Lifts and/or Carries: type amount of weight in each area
Maximum: 50(lbs) Frequently: 10-20 (lbs) Occasions: 50 (lbs)

Employee uses Hands for repetitive activities:

• a. Simple Grasping: Right, Constant Left, Occasional
• b. Pushing/Pulling: Right, Frequent Left, Frequent
• c. Fine Manipulation: Right, Occasional Left, Occasional

Employee uses Feet for repetitive activities:

• a. Right: None Left: None

Employee is required to perform these activities:

• a. Bending At Waist: Frequent
• b. Squatting: Occasional
• c. Climbing Ladders, Stairs: Occasional
• d. Kneeling On Ground: Occasional
• e. Reaching Above Shoulder: Occasional

Work Environment

The work environment characteristics described here are representative of those an employee encounters while performing the essential functions of this job (ie; heat/cold, dust/dampness, height; chemical; noise) PPE requirements are included. Reasonable accommodations may be made to enable individuals with disabilities to perform the essential functions.

Safety glasses always required

Chemical resistant gloves required when handling chemicals

Typical 10-hour workdays, frequent overtime required.

Annual Pulmonary Function Testing – Medical Clearance to wear a Respirator Annual Fit Testing – Testing of the Respirator to ensure it fits safety and securely.

Competencies

To perform the job successfully, an individual should demonstrate the following competencies:

• Teamwork:Balances team and individual responsibilities; Exhibits objectivity and openness to others' views; Gives and welcomes feedback; Contributes to building a positive team spirit; Puts success of team above own interests; Supports everyone's efforts to succeed.
• Motivation: Measures self against standard of excellence.
• Quality: Demonstrates accuracy and thoroughness; Applies feedback to improve performance; Monitors own work to ensure quality.
• Attendance/Punctuality: Is consistently at work and on time.
• Dependability: Takes responsibility for own actions.