ME Technician III

Jabil; Bayan Lepas; On-site; MYR 40,000 - 56,000; Full time

Job summary

Jabil in Bayan Lepas, Penang, Malaysia is seeking an Engineering Technician to maintain and develop machine programs, PD files, and machine set-ups on the SMT line. You will optimize programs and setups to meet theoretical run-rate and monitor line performance for maximum efficiency and quality.

Responsibilities include preventive maintenance, diagnosing non-SMT equipment, training operators, and supporting changeovers.

Qualifications

• Diploma / Certificate in engineering or two years related experience.
• Maintain and repair SMT equipment on assigned line(s).
• Perform preventative maintenance and diagnose non-SMT equipment.

Responsibilities

• Maintain and develop machine programs, PD files and machine set-ups.
• Optimize machine programs and set-ups to meet run-rate targets.
• Monitor line performance and drive efficiency and product quality.
• Provide training to operators and assist with changeovers to improve throughput.

Skills

Machine maintenance

Troubleshooting

Preventive maintenance

SMT equipment

Process optimization

Training

Education

Diploma/Certificate in Engineering

Two years related experience

Tools

CIQ

TARS

ICT Diagnostics

Solder paste printing

Job description

Job Description

• Maintain and develop machine programs, part definition (PD) files and machine set-ups.
• Optimize machine programs and set-ups to meet or exceed theoretical product run-rate.
• Observe machine and line performance and determine the necessary steps needed to achieve optimum line efficiency and product quality.
• Monitor CIQ, TARS, ICT Diagnostic defect analysis sheet, feeder data (and other available sources of information) continuously for tracking and gauging machine and process performance.
• Maintain and repair all SMT equipment on assigned line(s).
• Determine when necessary machine repairs are needed and perform out-of-cycle maintenance.
• Perform ‘as-required’ preventative maintenance of SMT equipment on assigned line(s).
• Perform initial diagnosis of non-SMT equipment on assigned line(s), and execute repairs within skill level. Escalate more complex issues to Industrial Techs, and provide assistance as needed to accomplish repairs.
• Assist Machine Operators on assigned line(s) by providing ongoing training and direction.
• Assist with machine operation in order to expedite changeover, cover breaks, or otherwise improve line efficiency.
• Interface with Line Supervisors, Manufacturing Engineers and Machine Support Manager to determine corrective actions needed, and be the front line person in ensuring that assigned line(s) performs with the maximum efficiency and product quality.
• Provide training to Manufacturing Engineering Tech I employees.
• Assist Manufacturing Engineers in achieving optimum process performance by measuring and / or optimizing of reflow profiles, wave solder profiles, and screen printing of solder paste.
• Provide recommendations for designing, fabricating and / or modifying necessary tooling, and product design for manufacturability (DFM) improvements.
• Provide daily ‘pass-down’ reports to Project Engineer, Manufacturing Engineer and the Manufacturing Engineering Technician on the following shift.
• Adhere to all safety and health rules and regulations associated with this position and as directed by supervisor.
• Comply with all procedures within the company security policy.

JOB QUALIFICATIONS

Knowledge Requirements

• Maintain and develop machine programs, part definition (PD) files and machine set-ups.
• Optimize machine programs and set-ups to meet or exceed theoretical product run-rate.
• Observe machine and line performance and determine the necessary steps needed to achieve optimum line efficiency and product quality.
• Monitor CIQ, TARS, ICT Diagnostic defect analysis sheet, feeder data (and other available sources of information) continuously for tracking and gauging machine and process performance.
• Maintain and repair all SMT equipment on assigned line(s).
• Determine when necessary machine repairs are needed and perform out-of-cycle maintenance.
• Perform ‘as-required’ preventative maintenance of SMT equipment on assigned line(s).
• Perform initial diagnosis of non-SMT equipment on assigned line(s), and execute repairs within skill level. Escalate more complex issues to Industrial Techs, and provide assistance as needed to accomplish repairs.
• Assist Machine Operators on assigned line(s) by providing ongoing training and direction.
• Assist with machine operation in order to expedite changeover, cover breaks, or otherwise improve line efficiency.
• Interface with Line Supervisors, Manufacturing Engineers and Machine Support Manager to determine corrective actions needed, and be the front line person in ensuring that assigned line(s) performs with the maximum efficiency and product quality.
• Provide training to Manufacturing Engineering Tech I employees.
• Assist Manufacturing Engineers in achieving optimum process performance by measuring and / or optimizing of reflow profiles, wave solder profiles, and screen printing of solder paste.
• Provide recommendations for designing, fabricating and / or modifying necessary tooling, and product design for manufacturability (DFM) improvements.
• Provide daily ‘pass-down’ reports to Project Engineer, Manufacturing Engineer and the Manufacturing Engineering Technician on the following shift.
• Adhere to all safety and health rules and regulations associated with this position and as directed by supervisor.
• Comply with all procedures within the company security policy.

Education & Experience Requirements

• Diploma / Certificate in an Engineering Field or minimum of two years related experience and/or training; or equivalent combination of education and experience.
• Equivalent combinations of education, training, and hands-on experience may be considered in lieu of formal qualifications