Calibration & Maintenance Engineer

EMS TEST MEASUREMENT SDN BHD; Seberang Perai; On-site; MYR 60,000 - 90,000; Full time

Benefits offered by this job

Health & medical insurance

Travel allowance

Performance incentives

Training & certification

Job summary

EMS Test Measurement Sdn Bhd is seeking a Calibration & Maintenance Engineer to perform calibration, preventive maintenance, troubleshooting and reporting for environmental test chambers and related equipment. The role focuses on accuracy, traceability, and timely service reports for customers across Malaysia.

Fresh graduates are welcome, with emphasis on hands-on technical work, problem-solving and precise documentation.

Qualifications

• Bachelor’s degree in Electrical, Electronics, Instrumentation, Mechatronics, Mechanical Engineering or a related field.
• Fresh graduates are encouraged to apply.
• Strong interest in calibration, equipment maintenance and hands-on technical work.
• Good problem-solving, analytical and communication skills.
• Attention to detail when recording measurements, checking calculations and preparing technical reports.

Responsibilities

• Perform calibration and verification of equipment at customer sites and in-house, following approved procedures and customer requirements.
• Record and analyse measurement results, identify deviations and document equipment conditions before and after adjustments.
• Prepare accurate calibration reports and certificates, including measurement results, reference equipment details and traceability information.
• Check calculations and supporting records before submitting reports for technical review and approval.
• Maintain calibration records and monitor the calibration status of reference instruments.
• Perform scheduled preventive maintenance on environmental test chambers and related test equipment.
• Inspect equipment, identify potential faults and recommend corrective actions to improve reliability and minimise downtime.
• Troubleshoot electrical, electronic, mechanical and control system issues within the assigned equipment scope.
• Support equipment installation, commissioning, repairs and performance checks following maintenance.
• Prepare maintenance checklists and service reports detailing findings, work completed and recommendations.
• Explain calibration results, equipment conditions and maintenance recommendations clearly to customers.
• Provide practical guidance on equipment operation, routine care and basic troubleshooting.
• Coordinate with internal teams and manufacturers to resolve technical issues and complete service work on schedule.
• Follow safety procedures and maintain proper handling of customer equipment and reference instruments.

Skills

Problem solving

Documentation

Analytical thinking

Teamwork

Education

Bachelor’s degree in Electrical, Electronics, Instrumentation, Mechatronics, Mechanical Engineering

Tools

Excel

MS Word

Job description

As a Calibration & Maintenance Engineer at EMS Test Measurement, you will perform equipment calibration, preventive maintenance, troubleshooting and performance verification, together with the preparation of accurate calibration and service reports.

Working with environmental test chambers, test systems and measuring instruments, you will help customers maintain equipment accuracy, reliability and operational readiness.

Fresh graduates and experienced candidates are welcome to apply. This role suits engineers who enjoy practical technical work, problem-solving and careful documentation.

Calibration & Reporting

Perform calibration and verification of equipment at customer sites and in-house, following approved procedures and customer requirements.

Record and analyse measurement results, identify deviations and document equipment conditions before and after adjustments, where applicable.

Prepare accurate calibration reports and certificates, including measurement results, reference equipment details and traceability information.

Check calculations and supporting records before submitting reports for technical review and approval.

Maintain calibration records and monitor the calibration status of reference instruments.

Preventive Maintenance & Troubleshooting

Perform scheduled preventive maintenance on environmental test chambers and related test equipment.

Inspect equipment, identify potential faults and recommend corrective actions to improve reliability and minimise downtime.

Troubleshoot electrical, electronic, mechanical and control system issues within the assigned equipment scope.

Support equipment installation, commissioning, repairs and performance checks following maintenance.

Prepare maintenance checklists and service reports detailing findings, work completed and recommendations.

Customer Support & Teamwork

Explain calibration results, equipment conditions and maintenance recommendations clearly to customers.

Provide practical guidance on equipment operation, routine care and basic troubleshooting.

Coordinate with internal teams and manufacturers to resolve technical issues and complete service work on schedule.

Follow safety procedures and maintain proper handling of customer equipment and reference instruments.

Requirements

Bachelor’s degree in Electrical, Electronics, Instrumentation, Mechatronics, Mechanical Engineering or a related field.

Fresh graduates are encouraged to apply.

Strong interest in calibration, equipment maintenance and hands‑on technical work.

Good problem‑solving, analytical and communication skills.

Attention to detail when recording measurements, checking calculations and preparing technical reports.

Proficiency in Microsoft Excel and Word.

Responsible, safety‑conscious and willing to learn.

Able to work effectively in a team and take ownership of assigned tasks.

Willingness to travel to customer sites for calibration and maintenance assignments.

Added Advantages

Relevant work experience, internships or academic projects involving calibration, equipment servicing, testing or technical support.

Knowledge of environmental test chambers, temperature and humidity measurement, or test and measurement equipment.

Familiarity with measurement uncertainty, metrological traceability and ISO/IEC 17025 requirements.

Ability to read electrical diagrams, technical manuals and equipment specifications.

Experience using data loggers, reference instruments or calibration software.

Perks and benefits Health & medical insurance coverage Travel allowance - Travel, Petrol, Parking Performance incentives / annual bonus Training & certification

We are a company specializing in Distributions of High Tech Electronics & Electrical Test & Measurement Equipment, Calibration and Repair Services, Training & Consultancy. With offices in Malaysia and Indonesia, we focus on various industries segment namely, Manufacturing, Broadcast & Video, Educations and Government Research Institution.

We optimize mobility opportunities and make effort to progress and succeed on challenges. Our people are committed, vibrant & productive and we aim to create a brighter future for generations to come.

“Our people are our greatest assets. Our mission is to surprise and delight our customers at every single imaginable touch-point – always”

To live up this statement, is entirely dependent on our people to continuously improve themselves – both personally as well as professionally. To do this our talent will be embedded not only “learn” so as to grow and develop, but to also “learn” to embrace change and collaborate more because we know that we are worth more and achieve more as a team than individually.

In tandem with our rapid growth and business expansion, we are looking for high achievers to be part of our dynamic team.