Electrical Engineer

Ooge Innovations; Bengaluru; On-site; INR 500,000 - 750,000; Full time

Job summary

Ooge Innovations in Bengaluru seeks a hands-on QA/test engineer to verify samples from manufacturing partners against specifications and to document results for CRS/BIS registration. You will test chargers, adapters, power banks, cables, and audio devices, ensuring safety and performance across multiple protocols.

Ideal candidates have 2–9 years in consumer electronics QA, with experience in interpretation of schematics, BOMs, and test equipment.

Qualifications

• B.E./B.Tech in Electrical/Electronics or equivalent.
• 2–9 years in product testing, QA or test lab, preferably consumer electronics.
• Hands-on with electronic loads, battery testers, power supplies and test gear.
• Knowledge of battery technology, charging circuits and protection circuits.
• Ability to read schematics, datasheets and BOMs.
• Familiar with BIS/CRS registration process and overseas partner coordination.
• Experience defining sampling plans and QA acceptance criteria.
• Proficient in recording data in Excel and ERP systems.

Responsibilities

• Test samples from manufacturing partners against specifications before orders.
• Verify rated vs measured output for chargers/adapters across voltages and protocols.
• Test battery capacity on power banks and record efficiency vs claims.
• Draw samples from each incoming lot and test before acceptance.
• Run functional checks on cables/connectors for integrity and cycles.
• Test audio products for output, pairing, and playtime on full charge.
• Check protection circuitry for trip conditions (OC, OV, SC, OT, over-discharge).
• Monitor temperature rise and hold any lot that fails until cleared.
• Coordinate sample submission with BIS labs for CRS/registration.
• Maintain test reports, certificates, and technical files; keep audit-ready.
• Verify markings and declarations match tested values per Metrology/E-Waste rules.
• Test warranty returns and field failures; establish root cause and responsibility.
• Initiate corrective actions with manufacturers and verify via re-testing.
• Maintain in-house test bench and calibration records.
• Write and maintain standard test procedures for each product category.
• Publish periodic quality reports covering pass/fail rates and defects.

Skills

Attention to detail

Analytical thinking

Strong communication

Education

B.E./B.Tech in Electrical/Electronics or E&C

Tools

Electronic loads

Battery testers

Power supplies

Oscilloscopes

Multimeters

LCR meters

Thermal measurement equipment

Job description

Role & responsibilities

• Test every new sample received from the manufacturing partner against the agreed specification before the sample is approved and the order is placed
• Verify rated output against measured output for chargers and adapters across voltage, current and all supported fast-charging protocols
• Verify battery capacity in mAh and Wh on power banks by controlled discharge and record actual conversion efficiency against the claimed figure
• Draw samples from every incoming production lot using a defined sampling plan and test before the lot is accepted into stock
• Run functional checks on cables and connectors covering continuity, current rating, data transfer and connector insertion cycles
• Test audio products for output level, channel balance, distortion, pairing behaviour, microphone function and playback time on a full charge
• Check protection circuitry by deliberate test over-current, over-voltage, short circuit, over-temperature and over-discharge must all trip as designed
• Monitor temperature rise under full load and raise a hold on any lot that fails, ensuring held stock is not released until cleared
• Coordinate sample submission, testing and documentation with BIS-recognised laboratories for registration under the Compulsory Registration Scheme
• Maintain test reports, certificates and technical files for each SKU and keep them current and audit-ready
• Verify that markings, ratings and declarations on the product and packaging match the tested values as required under Legal Metrology and E-Waste Rules
• Test warranty returns and field failures, establish root cause and classify each failure by type and responsibility
• Raise corrective action requests with the manufacturing partner and verify through re-testing that the corrective action worked
• Set up and maintain the in-house test bench, keep all instruments calibrated and maintain calibration records
• Write and maintain standard test procedures for every product category so testing is repeatable regardless of who performs it
• Publish a periodic testing and quality report covering pass and fail rates, recurring defects and supplier-wise performance
• Train and guide the quality inspection team on test procedures and acceptance criteria

Preferred candidate profile

• B.E. or B.Tech in Electrical, Electronics, Electronics and Communication or an equivalent discipline
• 2 to 9years of experience in product testing, quality assurance or a test laboratory, preferably in consumer electronics, mobile accessories or power electronics
• Hands-on experience with electronic loads, battery testers and analysers, power supplies, oscilloscopes, multimeters, LCR meters and thermal measurement
• Working knowledge of battery technology, charging circuits, power conversion and protection circuitry
• Ability to read and interpret electrical schematics, datasheets and BOMs
• Familiarity with Indian product safety standards and the BIS certification process
• Prior experience taking a consumer electronics product through BIS or CRS registration will be an advantage
• Experience defining sampling plans and acceptance criteria for incoming quality inspection
• Exposure to working with overseas manufacturing partners on quality issues and corrective action
• Knowledge of structured root cause analysis methods and quality tools
• Comfortable recording and analysing test data in Excel and in an ERP system
• The judgement and the nerve to reject a lot that does not meet specification, regardless of commercial pressure or dispatch deadlines