Welder 1 - 1st Shift

Nelson Global Products Inc.; Indianapolis (IN); On-site; USD 42,000 - 64,000; Full time

Job summary

Nelson Global Products Inc. in Indianapolis, IN is seeking a skilled Production/Welder Helper to read routing sheets, determine tooling, and set up for welded components. You will operate machines, run production, and conduct quality inspections per written procedures.

The role requires weld certifications, reading blueprints, and precise measurement with calipers. Day shift, strong safety focus, and opportunity to contribute to process improvements are offered.

Qualifications

• Must maintain certification on all welding methods required by NGP or our Customers.
• Demonstrated mechanical aptitude and shop math skills.
• Ability to read blueprints and follow setup instructions precisely.

Responsibilities

• Read setup sheets and routing packages to determine tooling and locations.
• Ensure settings meet requirements and obtain approvals as needed.
• Operate machines, run production, and perform quality inspections per procedures.
• Use inspection tools to measure welds and dimensions; watch for defects.
• Complete production records including scrap or rework reasons.
• Move parts with pallet jack and assist in updating setup sheets.
• Participate in continuous improvement and safety procedures.

Skills

Mechanical aptitude

Shop math

Blueprint reading

Problem solving

Read and follow routing instructions

Education

Welding certification

Tools

Tape measure

Dial calipers

Surface plate

Job description

2840 Fortune Cir W, Suite C
Indianapolis, IN 46241, USA

Description

POSITION OVERVIEW:

PRIMARY ACCOUNTABILITIES:

• Read previously prepared setup sheets and routing package for individual parts. Determines what tooling is needed and where it is located.
• Follows established set-up requirements and ensures settings are correct.
• Receives approval on setup pieces as required.
• Operates machine to run production and perform quality inspections as required by the written Quality Procedures. Makes necessary adjustments during production runs to stay in tolerances.
• May use templates, fixtures, surface plate, calipers, snap gauges, or other inspection tools to measure welded components, bead size, or other necessary dimensions per blueprint. Watches for presence of burn through, cold starts, lack of penetration, bead size, or other indications of suspect welds.
• Complete records of production including scrap or rework reasons.
• Move parts to the subsequent operation with pallet jack.
• Assists Group leader in writing new or changing existing Setup Sheets. May assist Engineering in developing new processes and trying out new tooling.
• Participate in the corrective action process to prevent defects from recurring.
• Follow procedures consistently to obtain repeatability.
• Participate in team meetings seeking continuous improvements for the operation.
• Observe all safety and OSHA procedures and standards. Maximum lifting of 25lb without assistance. PPE is required at times.
• Ability to read tape measurements.
• Ability to read manual calipers.
• Ability to read and understand blueprints

Job Requirements:

• Must maintain certification on all welding methods required by NGP or our Customers.
• Must have demonstrated mechanical aptitude, proficiency in shop math (fractions, decimals, metric), ability to read and follow specific routing instructions, ability to read and understand setup instructions, ability to read blueprints, proficiency in the use of appropriate measuring instruments (tape measure, dial calipers), ability to check quality of parts against templates.
• Must pass the NGP Weld Test.
• Must have demonstrated ability to handle production requirements and demonstrated problem solving ability from previous work.
• Must have the ability to stand for 8-hour shift or longer. Able to bend, twist, stoop to remove parts from baskets and lift to work area. Able to load parts into work area and complete baskets without damaging the part. Good hand and eye coordination.
• Must have hand tools necessary to inspect parts and adjust machines.

First Shift Hours:

Monday - Friday 5:00 a.m. - 3:30 p.m. (Saturday's Overtime)

Equal Opportunity Employer/Protected Veterans/Individuals with Disabilities

The contractor will not discharge or in any other manner discriminate against employees or applicants because they have inquired about, discussed, or disclosed their own pay or the pay of another employee or applicant. However, employees who have access to the compensation information of other employees or applicants as a part of their essential job functions cannot disclose the pay of other employees or applicants to individuals who do not otherwise have access to compensation information, unless the disclosure is (a) in response to a formal complaint or charge, (b) in furtherance of an investigation, proceeding, hearing, or action, including an investigation conducted by the employer, or (c) consistent with the contractor’s legal duty to furnish information. 41 CFR 60-1.35(c)

Equal Opportunity Employer/Protected Veterans/Individuals with Disabilities

This employer is required to notify all applicants of their rights pursuant to federal employment laws.For further information, please review the Know Your Rights notice from the Department of Labor.