Robotics Technician (Contract)

Galactic Resource Advancement Mechanism Technologies Corporation; El Segundo (CA); On-site; USD 62,000 - 83,000; Full time

Job summary

Galactic Resource Advancement Mechanism Technologies Corporation (GRAM) in El Segundo, CA, seeks a Robotics Technician (Contract) to build, wire, instrument, inspect, and test insectoids and their subsystems on-site.

You will convert engineering releases into hardware, document results, and ensure build condition using measurements, cables, connectors, and calibration artifacts. This role requires hands-on work with electromechanical assemblies and strict workspace controls.

Qualifications

• Experience assembling, testing, maintaining electromechanical hardware.
• Built or serviced hardware from drawings, schematics, bills of material.
• Proficiency with torque fastening, connector assembly, soldering, and inspection.
• Used measurement/diagnostic tools to accept or troubleshoot hardware.
• Documented nonconformances and corrective actions.

Responsibilities

• Assemble subsystems from drawings, BOMs, schematics, and revisions.
• Fabricate, route, terminate, label, inspect, and test wiring harnesses and sensor leads.
• Install instrumentation and operate meters and test equipment.
• Perform subsystem checkout, calibration, and functional tests.
• Diagnose discrepancies and escalate as needed.
• Execute approved rework and verify restored condition.
• Maintain build travelers, traceability, and test result records.

Skills

Mechanical assembly

Electrical workmanship

Soldering

Crimping

Documentation

Tools

Multimeters

Oscilloscopes

Calipers

Micrometers

Data acquisition

Job description

Robotics Technician (Contract)

The Mission

GRAM is a self replication company creating populations of insectoids for the physical economy.

Our first research frontier is self-preservation: the base case of physical self-replication. Our machines will survive, coordinate, and recover without humans. We believe scalable machine labor requires more than single-agent task generality or machines shaped in our image.

About the role

You will build, wire, instrument, inspect, rework, service, and test insectoids and their subsystems. You will turn engineering releases into physical hardware, identify discrepancies before they become ambiguous machine failures, and maintain records connecting every test result to the actual article on the floor. You will execute controlled work across fasteners, connectors, harnesses, bearings, sensors, adhesives, and calibration artifacts; surface defects quickly; and use measurements and documented discrepancies to restore the required build condition and improve product and process.

What you will do

• Assemble mechanical and electromechanical subsystems from drawings, bills of material, schematics, work instructions, torque requirements, and controlled revisions.
• Fabricate, route, terminate, label, inspect, and test wiring harnesses, connectors, sensor leads, and low-voltage power or communication assemblies.
• Install instrumentation and operate multimeters, oscilloscopes, bench supplies, torque tools, force or displacement sensors, data-acquisition equipment, and dimensional inspection tools.
• Perform subsystem checkout, continuity and insulation checks, leak or motion checks where applicable, calibration support, functional test, and machine bring-up under approved procedures.
• Diagnose build and service discrepancies using direct inspection, measurements, drawings, schematics, logs, and known-good comparisons; escalates beyond technician authority.
• Execute approved rework, repair, maintenance, and part replacement, then verify the restored condition through documented inspection and retest.
• Maintain build travelers, serial and lot traceability, tool and equipment status, configuration records, discrepancy reports, photographs, test results, and as-built feedback.

Minimum qualifications

• Professional experience assembling, testing, maintaining, or servicing complex electromechanical hardware whose work was accepted against documented requirements.
• Built or serviced complex electromechanical hardware from controlled mechanical drawings, electrical schematics, bills of material, and written procedures.
• Demonstrated proficiency in mechanical assembly and electrical workmanship, including torque-controlled fastening, connector assembly, crimping, soldering, wire identification, continuity testing, and visual inspection.
• Used measurement and diagnostic equipment such as calipers, micrometers, multimeters, oscilloscopes, bench power supplies, torque tools, or data-acquisition systems to accept or troubleshoot hardware.
• Documented a nonconformance or build discrepancy, executed or supported controlled corrective work, and verified closure through inspection or functional retest.

Preferred experience

• Robotics, aerospace, automotive, medical-device, industrial-automation, or other low-volume complex hardware.
• Motor, gearbox, bearing, sensor, PCB, harness, battery, pneumatic, vacuum, adhesive, or precision-mechanism assembly and test.
• Prototype bring-up, environmental or lifecycle testing, machine-shop coordination, calibration systems, or configuration-controlled service work.

Additional requirements

• This role requires regular movement around a robotics workspace and sustained hands-on work with tools, fixtures, test equipment, and powered electromechanical systems. You must follow required workspace controls, lockout or de-energization procedures, and personal protective equipment requirements.

Compensation and contract

The hourly pay range for this El Segundo, California position is $45.00-$60.00 per hour. This is an on-site, hourly W-2 contract assignment supporting an immediate need. The position is non-exempt; overtime will be paid in accordance with applicable law. Please tell us your earliest available on-site start date. Assignment duration, schedule, and benefits will be discussed during the hiring process. We treat your work and conversations with discretion.