Quality Inspector II

Cadrex; Seguin (TX); On-site; USD 52,000 - 70,000; Full time

Benefits offered by this job

Health/dental/vision coverage

401(k) with employer match

Paid time off and holidays

Education support program

Disability insurance

Life insurance

Job summary

Cadrex in Seguin, TX is seeking a Quality Inspector II to support site manufacturing through development, evaluation, and continual improvement of processes to meet customer quality expectations.

You will read blueprints, perform visual and dimensional inspections, document results, quarantine non-conforming product, operate FARO & Micro-Vu, and mentor Level I inspectors while contributing to lean improvements.

Qualifications

• High school diploma or equivalent; associate degree preferred.
• 3+ years in metal fabrication inspection in a continuous improvement QMS preferred.
• Ability to read and interpret blueprints and perform dimensional inspection.

Responsibilities

• Perform visual and dimensional inspections of in-process and finished products.
• Document inspection results and reports; quarantine non-conforming products.
• Operate FARO and Micro-Vu measurement equipment; support calibration activities.

Skills

Calipers

Micrometers

Blueprint reading

Visual inspection

Documentation

Non-conforming handling

Measurement equipment calibration

Education

High school diploma

Associate degree in related field preferred

Tools

FARO

Micro-Vu

Job description

DescriptionOVERVIEWCadrex is searching for a Quality Inspector II to directly support site manufacturing practices through development, evaluation, and continual improvement of processes using quality concepts, principles, and methodologies with the goal of consistently meeting or exceeding customer expectations of quality.

KEY RESPONSIBILITIES

• Use measuring devices such as calipers, micrometers, steel rulers, pin gages, surface plate, and height gage
• Read and interpret blueprints
• Visual inspection of product according to customer requirements
• Inspect and or test in-process product as well as finished product
• Document inspection results by completing required reports/logs
• Identify and quarantine all non-conforming product
• Generate and summarize non-conforming reports for discrepant product
• Keep measurement equipment operating by following operating instructions and identify and address issues with equipment that may need repair
• Inspect and approve incoming materials where and when needed by confirming they meet specifications
• Attend department meetings as required
• Inspect and release products for shipping by ensuring proper documentation or certifications are provided as outlined by customer requirements. (Visual & Dimensional verification may be required)
• Learn and assist with dimensional verification of PPAP and 1st article parts
• Create internal Control Plans in accordance with customer and Advanced Laser requirements
• Operate FARO & Micro-Vu measurement equipment
• Provide direct support to the production floor by assisting with interpretation and development of manufacturing related documentation and providing proper measuring techniques
• Assist with calibration procedures and provide calibration of measuring equipment as outlined by site procedures and ISO Standard
• Lead and train Level I inspectors as needed to increase performance
• Train, identify, and implement lean process and project improvements

Requirements

PREFERRED QUALIFICATIONS

• Understand industry safety standards and quality expectations
• 3 or more years working in a metal fabrication environment under a continuous improvement QMS with hands on inspection preferred
• Read and comprehend simple instructions, short correspondence, and memos.
• Write simple correspondence
• Ability to effectively present information in one-on-one and small group situations to customers, clients, and other employees
• Ability to add, subtract, multiply, and divide in all units of measure, using whole numbers, common fractions, and decimals
• Ability to compute rate, ratio, and percentage and to draw and interpret graphs
• Knowledge of word processing software, spreadsheet software, e-mail software and the use of the internet

EDUCATION

High school diplomaAssociate degree in related field preferred

LOCATION

Onsite

SCHEDULE

M-F; 6:00am - 3:00pm

WORK ENVIRONMENT

While performing the duties of this job, the employee is frequently exposed to work near moving mechanical parts and vibration. The employee is occasionally exposed to the risk of electrical shock. The noise level in the work environment is usually moderate and occasionally loud.

PHYSICAL DEMANDS

While performing the duties of this job, the employee is regularly required to stand, sit, use hands and fingers, handle or feel, and talk or hear. The employee is occasionally required to sit; climb or balance; stoop, kneel, crouch, or crawl. The employee must occasionally lift and/or move up to 25 pounds. Specific vision abilities required by this job include close vision, distance vision, peripheral vision, color vision, depth perception and ability to adjust focus.

CADREX'S CORE VALUES

Safety first, rising to the challenge, collaboration, accountability, and doing the right thing

TOTAL COMPENSATION INCLUDES

• Health/dental/vision coverage
• Employer-paid and supplemental life insurance
• Short- and long-term disability insurance
• Generous paid time off and holiday pay
• Monthly remote work stipend (for remote employees who qualify)
• 401(k) investment plan, with an employer match of up to 4%
• Education support program
• Safety eyeglasses/shoe reimbursement
• Referral bonuses
• Bonus plan for all full-time employees

ABOUT US

CADREX Manufacturing Solutions is a leading provider of complex sheet metal and machined production parts, assemblies, and weldments for a variety of end markets, including electrical transmission and distribution, warehouse automation, technology, aerospace & defense, medical, food, and industrials. With locations in Colorado, Pennsylvania, Illinois, Washington, Wisconsin, Minnesota, Michigan, Indiana, Massachusetts, Oklahoma, and Monterrey Mexico, CADREX offers numerous in-house manufacturing capabilities, including laser cutting, sheet metal fabrication, complex assembly, CNC punching, CNC machining, forming, robotic welding, stamping, fastener insertion, and tool and die manufacturing, to effectively serve customers with lights-out manufacturing capabilities for mid- to high-volume production. For more information, visit www.cadrex.com.

Cadrex provides equal employment opportunities to all employees and applicants for employment and prohibits discrimination and harassment of any type without regard to race, color, religion, age, sex, national origin, disability status, genetics, protected veteran status, sexual orientation, gender identity or expression, or any other characteristic protected by federal, state, or local laws. This policy applies to all terms and conditions of employment, including recruiting, hiring, placement, promotion, termination, layoff, recall, transfer, leaves of absence, compensation, and training.