MECHANICAL ASSEMBLER

Gedusa; Solon (OH); On-site; USD 25,000 - 30,000; Full time

Job summary

Gedusa in Solon, OH is seeking a skilled mechanical assembler to construct, repair and service GED machines. You will work from blue prints, assembly drawings, and written instructions to assemble, adjust and test units.

Responsibilities include using calipers, micrometers, and dial indicators; following BOMs and routings; inspecting parts for defects; and safely operating overhead cranes. Minimum 2 years in production/assembly preferred.

Qualifications

• Education: High School Diploma or equivalent required.
• Must read and interpret mechanical, pneumatic, hydraulic and electrical drawings.
• Experience: 2+ years in production/assembly preferred.

Responsibilities

• Lay out, plan and perform mechanical assemblies including subassemblies and mounting of components with high accuracy for close tolerance assembly.
• Obtain parts per BOM and shop floor routings; check for defects before installation.
• Assemble from drawings and schematics; verify finished work adheres to specifications.

Skills

Troubleshooting

Reading drawings

Attention to detail

Team collaboration

Education

High School Diploma or equivalent

Tools

Calipers

Micrometers

Dial indicators

Electrical schematics

Job description

Construct, assemble, or rebuild GED machines. Working with blue prints, assembly drawings,

specifications, sketches, and verbal and written instructions, assembles, disassembles, repairs and

adjusts a variety of units, attachments, components and/or accessories.

Duties and Responsibilities

• Lay out, plan and perform a wide variety of mechanical assemblies consisting of but not limited to subassembly work, mounting of commercial components (bearings, pneumatic components and drive systems) to large and small frame weldments. High degree of accuracy required for close tolerance assembly involving bearing surface fit, machine bed surface assembly.
• Working from bill of material (B.O.M.) and shop floor routings, obtain parts and components necessary for assigned tasks.
• Check for apparent defects, damage to all components prior to installation/assembly.
• Work from mechanical drawings, pneumatic and hydraulic schematics, written, verbal, and own knowledge for determining location and placement of commercial components, pneumatic and hydraulic assemblies, machined parts and fabricated parts.
• Check finished work for integrity and adherence to specification.
• Start-up and test finished machinery per specifications.
• Use common power tools, as well as hand and measuring tools (calipers, micrometers, dial indicators).
• Perform inventory control procedures with regards to cycle counting, verification of on hand balances and report part discrepancies, B.O.M. and routing errors.
• Report time, production or other required information on proper forms.
• Detect and report faulty equipment, material, or other unusual conditions to proper supervision.
• Observe all prescribed safety rules and regulations.
• All other duties as assigned.

Req

Requirements

Education High School Diploma or equivalent required.

Specialized knowledge

• Working knowledge of basic measuring instruments such as calipers, micrometers and dial indicators.
• Working knowledge of machine electrical controls and functionality.
• Must read and interpret mechanical, pneumatic, hydraulic and electrical drawings.

Skills

• High degree of troubleshooting skills is necessary as well as the ability to interface with engineering personnel with regards to machine performance and functionality.

Abilities

• Must be able to safely operate overhead crane.

Desired Characteristics

• Attention to Detail — Job requires being careful about detail and thorough in completing work tasks.
• Dependability — Job requires being reliable, responsible, and dependable, and fulfilling obligations.
• Cooperation — Job requires being pleasant with others on the job and displaying a goodnatured, cooperative attitude.
• Persistence — Job requires persistence in the face of obstacles.
• Initiative — Job requires a willingness to take on responsibilities and challenges.

Experience

• Minimum 2 years’ experience in a production/assembly environment preferred.

Working Conditions and Physical Requirements

• While performing the duties of this job, the employee is frequently required to stand, sit and walk. The employee regularly uses hands and fingers. The employee must also be capable of bending, reaching, kneeling, crouching, and climbing. The employee must regularly lift, push, pull, and/or move up to 50 pounds.
• While performing the job light to moderate physical activity, performing strenuous daily activities of a product/technical nature is required.
• While performing the job the employee may be exposed to various environmental conditions, loud noise levels and more frequently working around mechanical parts.
• To perform this job successfully, an individual must be able to perform each essential duty satisfactorily. The requirements listed above are representative of the knowledge, skill, and/or ability, and physical demands required. Reasonable accommodations may be made to enable individuals with disabilities to perform the essential functions.