Heat Treat Operator 3rd Shift

Eaton Corporation; Cleveland (OH); On-site; USD 33,000 - 47,000; Full time

Job summary

Eaton is seeking a Heat Treat Operator for the Euclid, OH facility on 3rd shift (12am–7am, Mon–Fri). You will set up and run burnishing, nitride and heat-treat processes, inspect parts and document results per ANSI/ISO standards. Must have a high school diploma and GD&T experience; ITAR compliance required.

Position offers a 35-hour week with paid 40 hours and an hourly rate around $28.98 plus $1 shift differential. Benefits and equal opportunity statements apply.

Qualifications

• High School Diploma or GED from an accredited institution.
• Must reside within a 50-mile radius of work location; no relocation benefit is provided.
• This position requires use of information or access to hardware which is subject to ITAR. All applicants must be U.S. persons within the meaning of ITAR.
• Minimum one (1) year of machining/utility, heat treat or nitride experience.
• Minimum 2-year GD&T Experience (successful completion of Eaton Level 1 Advanced Training will be considered in lieu of this requirement).

Responsibilities

• Load, unload and monitor processing of parts in heat treat basket, load furnaces, operate furnaces, monitor gages, unload furnaces, and perform hardness test.
• Perform various burr, buff, dry blast, degrease and oiling operations on hardware.
• Set up, operate, monitor, read, interpret, and maintain furnace, atmosphere generation, and quench equipment controls and instruments such as timers, temperature control and monitoring recorder charts, flow scopes, pressure gages, various dial gages.
• Set up and operate all equipment with a minimum of assistance, be familiar with work procedures involved with nitride, heat treating, and buffing operations.
• Mount and accurately align various jig and fixtures, select speeds, and feeds. Load and align tooling working from engineering layouts.
• Read and interpret moderately complicated blueprints and execute quality checks using a variety of mechanical and electronic gages.
• Maintain accurate lot control (QCP 6.0) traceability, record keeping, log book entries, NCR’s (QCP 11.0) and associated documentation.
• Generate close tolerance edge breaks using various hand tools.
• Maintain clean equipment and work area, Perform minor machine maintenance as needed.
• Chart and plot data per SPC requirement.
• Move material within the cell.

Skills

Machining/utility/heat treat or nitide

GD&T experience

Vision test

Certified Operator

5S

Education

High School diploma or GED

Job description

Eaton’s AER FMC Fuel Motion Control Systems division is currently seeking a Heat Treat Operator 3rd Shift at our Euclid, OH facility! Core hours for 3rd shift are 12am - 7am Monday - Friday. This is a 35 hour work week, but you will be paid for a full 40 hour week. The hourly rate for this position is $28.98 plus $1/hr shift differential per hour. Please note the salary information shown above is a general guideline only. Salaries are based upon candidate skills, experience, and qualifications, as well as market and business considerations.

What you’ll do:

Job Summary:

• Set up and operate various burring, cleaning, buffing and blasting machines to generate rough and finish dimensions on a variety of parts. Perform operations such as nitride, heat treat, buff and blast. Also perform hand operations required to burr, polish, finish, and blend surfaces on machined parts.
• Perform visual and dimensional inspections and maintain accurate documentation on a variety of parts in accordance with ANSI Y14-5 and the Certified Operator program.
• Assistance may be given to other operators on proper operational procedures.

Job Responsibilities:

• Load, unload and monitor processing of parts in heat treat basket, load furnaces, operate furnaces, monitor gages, unload furnaces, and perform hardness test.
• Perform various burr, buff, dry blast, degrease and oiling operations on hardware.
• Set up, operate, monitor, read, interpret, and maintain furnace, atmosphere generation, and quench equipment controls and instruments such as timers, temperature control and monitoring recorder charts, flow scopes, pressure gages, various dial gages. Instruments may be analog or digital (programmable microprocessor) based.
• Set up and operate all equipment with a minimum of assistance, be familiar with work procedures involved with nitride, heat treating, and buffing operations. Frequent changes in set-up and maintenance of close tolerance require constant attention.
• Mount and accurately align various jig and fixtures, select speeds, and feeds. Load and align tooling working from engineering layouts. Adjust stops and cams to produce finish dimensions to tolerances.
• Read and interpret moderately complicated blueprints and execute quality checks using a variety of mechanical and electronic gages.
• Maintain accurate lot control (QCP 6.0) traceability, record keeping, log book entries, NCR’s (QCP 11.0) and associated documentation. *(Reordered)
• Generate close tolerance edge breaks using various hand tools.
• Maintain clean equipment and work area, Perform minor machine maintenance as needed.
• Chart and plot data per SPC requirement.
• Move material within the cell.

Qualifications:

• High School Diploma or GED from an accredited institution.
• Must reside within a 50-mile radius of work location; no relocation benefit is provided.
• This position requires use of information or access to hardware which is subject to the International Traffic in Arms Regulations (ITAR). All applicants must be U.S. persons within the meaning of ITAR. ITAR defines a U.S. person as a U.S. Citizen, U.S. Permanent Resident (i.e. 'Green Card Holder'), Political Asylee, or Refugee.
• Minimum one (1) year of machining/utility, heat treat or nitride experience.
• Minimum 2-year GD&T Experience (successful completion of Eaton Level 1 Advanced Training will be considered in lieu of this requirement).

Skills:

• Pass an Eaton vision test.
• Become a Certified Operator.
• Perform 5S and other duties as assigned.
• Complete Basics of Measurement courses.

#LI-CD1

We are committed to ensuring equal employment opportunities for all job applicants and employees. Employment decisions are based upon job-related reasons regardless of an applicant's race, color, religion, sex, sexual orientation, gender identity, age, national origin, disability, marital status, genetic information, protected veteran status, or any other status protected by law.

Eaton believes in second chance employment. Qualified applicants with arrest or conviction history will be considered regardless of their arrest or conviction history, consistent with the Los Angeles County Fair Chance Ordinance, the California Fair Chance Act and other local laws.

You do not need to disclose your conviction history or participate in a background check until a conditional job offer is made to you. After making a conditional offer and running a background check, if Eaton is concerned about conviction that is directly related to the job, you will be given the chance to explain the circumstances surrounding the conviction, provide mitigating evidence, or challenge the accuracy of the background report.

To request a disability-related reasonable accommodation to assist you in your job search, application, or interview process, please call us at 1-800-836-6345 to discuss your specific need. Only accommodation requests will be accepted by this phone number.

We know that good benefit programs are important to employees and their families. Eaton provides various Health and Welfare benefits as well as Retirement benefits, and several programs that provide for paid and unpaid time away from work. Click here for more detail: Eaton Benefits Overview. Please note that specific programs and options available to an employee may depend on eligibility factors such as geographic location, date of hire, and the applicability of collective bargaining agreements.