Finisher I (Metal Sanding)

ES Utilities South Dakota-USA; Ocala (FL); In loco; USD 25.000 - 39.000; Tempo pieno

Descrizione del lavoro

E-ONE in Ocala, FL is seeking a skilled body shop technician to perform sanding, grinding, mounting and prep for welding and finish work on large, custom vehicles. You will follow process sheets, inspect surfaces and ensure finishes meet cosmetic and structural specs, while maintaining safety standards.

You must handle lifting and physical tasks, operate hand and power tools, and contribute to continuous improvement with attention to quality and efficiency.

Competenze

• Must meet safety and quality standards within company guidelines.
• Able to follow process sheets, shop orders, prints and instructions.
• Must be physically able to lift up to 45 lb and perform long periods of standing.

Mansioni

• Sand or grind prep for welding and make surfaceFinish adjustments.
• Review materials, obtain tools, and move to work area.
• Inspect components for dents, defects, and surface conditions; apply finishing touches.
• Follow work standards and maintain a clean, safe work area.

Conoscenze

Safety

Quality

Flexibility

Initiative

Teamwork

Career development

Strumenti

Hand tools

Powered tools

Spraying equipment

Forklift

Fixtures

Sanders

Grinders

Tape measures

Squares

Files

Descrizione del lavoro

Job Summary:

Perform duties to sand, grind, mount, or repair any unit preparation for welding, assembly operations or paint, to meet specifications as part of the manufacture of large, custom, special purpose vehicles, working within the limits of prescribed routines.

Essential Functions:

• May sand or grind pats or bevel edged in preparation for welding. May feather, flute, flat and level grind, remove server corners to overcome surface stress areas subject to fatigue fractures or perform other similar conditions. May remove sharp edges or burns, detect dents, holes and substrate Work from process sheet, shop orders, prints, schedule, pick-lists, and instructions.
• Review material and production requirements. Obtain and accumulate tools and materials, move to work area.
• Blow off and wipe down components or unit to remove grit, grease and other foreign surfaces. Check cab, body or component structure for obvious defects such as dents in panel sections, rough welds beads, fractures, undulations or wavy surfaces and similar conditions.
• defects, apply fillers, file or sand area to meet surface finish requirements. May apply primer over corrected areas of body and expose aluminum.
• May wire brush welds to remove smoke, grind and remove excess weld beads to smooth surface, remove residue from weld area, and apply compound and buff surface to meet cosmetic criteria and specifications. Recognize and call attention to weld defects such as fractures, voids, porosity and distortion. Check and recognize part surfaces requiring smooth surfaces, sand and apply polishing compound and buff as required. Change grades of abrasive or compounds to suit finishing requirements and to finish surfaces of parts to prepare for future processing or as a final process, clean and buff surfaces such as tread plate, and remove scratches on non-painted surfaces.
• May remove doors or other components and place on work stand or fixture, pull required hinges and backup nars and mount in place.
• May flat surface sand specified pieces and vary pressure of sander to obtain symmetrical pattern across surface to meet cosmetic requirements.
• Monitor the quality of work performed in assigned area of responsibility.
• Follow work standards
• Must be able to perform within physical requirements including, but not limited to 45 lb. single lift; walking, kneeling, squatting and standing for long periods of time.

Other Duties May Include, But Are Not Limited To:

• Perform or assist with any operations, as required or directed, to maintain work flow or respond to production requirements.
• May be required to perform other duties not listed but needed by Supervisor in order to keep trucks on schedule.

Tools And Equipment Used :

Hand and powered tools, spraying equipment, forklift, fixtures, sanders, grinders, tape measures, squares, files.

Position Expectations:

1. SAFETY: Follow E-ONE General Health & Safety Rules, ensure safe operating conditions within area of responsibility, and notify coworkers and supervisors of hazardous acts and conditions. Proper use of PPE; use only defect-free equipment. Promote safety in department. Use proper lifting techniques and overhead hoist when needed. Maintain clean and safe working environment in line with 5-S Philosophy. Participate in hazardous communication training and safety meetings.
2. QUALITY: Responsible for the quality of work. This requires defect-free work and understanding of the requirements of the company's quality system as it pertains to job duties and responsibilities. Must be able to check work to ensure conformance to process control instructions, specifications, and quality standards. Identify and segregate non-conforming product. Identify the need for and assist in initiating and implementing corrective and preventive actions when appropriate.
3. FLEXIBILITY: Able and willing to work in other areas as needed. Must be flexible in taking lunch and breaks when workflow requires. Willing and able to meet overtime requirements as necessary.
4. INITIATIVE: Actively participate in continuous improvement of products and processes to better serve customers and improve the overall profitability of E-ONE. Actively seek out work in other areas when current assignment is complete. Make suggestions for improving product quality, processes, safety, and company profitability.
5. TEAMWORK: Positive working attitude toward other employees; be a team player. Work with others constructively and abide by company policies and procedures. Working together as a team for continuous improvement is vital to ensure the future of E-ONE and its employees. Teamwork will be required to be effective in daily production assignments as well as special improvement projects.
6. CAREER DEVELOPMENT: Attend and participate in a variety of meetings, training programs, and task force groups to integrate activities, communicate issues, obtain approvals, resolve problems, and maintain specific level of know