Electronic Repair Technician

Insight Global; Austin (TX); On-site; USD 60,000 - 85,000; Full time

Job summary

Insight Global is hiring a Bench Technician with significant electronic repair experience to work in the Internal Repair Facility. The role involves diagnosing, repairing, modifying, testing or verifying sub-components of a wide variety of complex automatic/logic-controlled electronics or electro-mechanical equipment at the component level.

You will use diagnostic techniques and operate advanced instrumentation, reading schematics and following safety procedures.

Qualifications

• Associate degree in Electronics or equivalent required.
• Minimum 5 years’ bench repair experience in electronics.
• Experience with AC/DC circuit design and troubleshooting.
• Ability to read schematics and understand circuits.
• Experience with test equipment: scopes, meters, generators.
• Repair of complex PCBs and controllers to component level.
• Post-repair testing and load/signal testing capabilities.
• High power DC supply repair and calibration experience.
• Servo/stepper motor repair and testing experience.
• Advanced knowledge of analog/digital circuits and tools.
• LabVIEW, Multi-Sim, Cadence or equivalents.
• Hardware programming concepts (VHDL/Verilog) desirable.

Responsibilities

• Diagnose, repair, modify, test or verify sub‑components of complex electronics.
• Work independently on assigned repairs in a high-pressure environment.
• Interface with customers, staff and management as needed.
• Set up and operate complex instrumentation for testing.
• Follow safety procedures, including electrical, chemical and mechanical.

Skills

Bench repair

AC/DC circuit design

Soldering (through-hole & surface)

Read schematics

Oscilloscope usage

Voltage meters / testing equipment

PCB/Controller repair

Post-repair testing

High power DC supply repair

Servo/Stepper motor repair

LabVIEW / Multi-Sim / Cadence

VHDL/Verilog

Education

Associate degree in Electronics

Tools

LabVIEW

Multi-Sim

Cadence

Oscilloscope

Multimeter

Signal generators

Job description

Insight Global is hiring for a Bench Technician with significant electronic repair experience to work in the Internal Repair Facility. The purpose of the job is to diagnose, repair, modify, test or verify sub-components of a wide variety of complex automatic/logic-controlled electronics or electro-mechanical equipment at a component level. Important duties include using diagnostic techniques; improvising circuits or equipment to special needs; working independently on assigned repairs; performing complex analysis of major malfunctions to the component level. Important skills and abilities include setting up, operating and adjusting complex instrumentation; knowledge of analog, digital, moderate circuit design abilities; above average level of mechanical ability (i.e. considerable knowledge of pneumatics, hydraulics and fluidics, working on your own vehicle); and safe working procedures.

Individual must be able to work with minimum supervision in high pressure environment, subject to shifts in priorities. Individual must be able to effectively interface with customers, employees and management. Candidate needs to have basic knowledge of Microsoft Office. Individual must be able to lift 50+ pounds in the course of carrying out job duties and follow all safety procedures, including but limited to electrical, chemical and mechanical safety procedures.

Skills and Requirements

• Minimum associates degree in Electronics
• Minimum 5 years’ experience working in bench repair field
• Experience in AC/DC circuit design
• Perform trouble shooting on items in need of repair.
• Perform through-hole, surface mount and fine pitch soldering
• Have skills to read schematics and understand circuits.
• Use testing equipment such as voltage meters, ESR, Oscilloscope, signal generators etc.
• Repair complex PCB and Controllers using root cause methodology down to component level.
• Able to perform post repair testing with knowledge of load testing and or signal generation.
• High Power DC supply repair, testing and calibration ranging from 1kW to 80kW.
• AC and DC Servo/Stepper motor rebuild and test.
• Advanced experience in AC and DC circuitry, advance test equipment, simulation software, and discrete semiconductor characteristics.
• Labview, Multi-Sim, Cadence or equivalent electrical design software.
• Hardware programming language (VHDL, Verilogic, JTAG, etc.)

We are a company committed to creating diverse and inclusive environments where people can bring their full, authentic selves to work every day. We are an equal employment opportunity/affirmative action employer that believes everyone matters. Qualified candidates will receive consideration for employment without regard to race, color, ethnicity, religion, sex (including pregnancy), sexual orientation, gender identity and expression, marital status, national origin, ancestry, genetic factors, age, disability, protected veteran status, military or uniformed service member status, or any other status or characteristic protected by applicable laws, regulations, and ordinances. If you need assistance and/or a reasonable accommodation due to a disability during the application or the recruiting process, please send a request to [e-mail].