Electrical Panel Assembly 840384

Alliance Industrial Solutions; Morrisville (NC); On-site; USD 34,000 - 41,000; Full time

Job summary

Alliance Industrial Solutions in Morrisville, NC is hiring an Electrical Panel Builder & Field Technician. You will start with 3 to 6 months of hands-on shop training to master control panel builds, wiring standards, and testing procedures.

After training, you will split time between shop fabrication and field installations, including conduit runs and machine startups at customer sites. A 1+ year background in electrical work and the ability to read schematics are required.

Qualifications

• 1+ years of hands-on experience in electrical control panel building or electrical work.
• Able to read and interpret electrical schematics and wiring diagrams independently.
• Conduit bending (EMT/Rigid) and wire pulling are preferred.
• Solid understanding of 480V 3-phase power and 24VDC control circuits.
• Proficiency using digital multimeters, megohmmeters, and hand/power tools.
• Willingness to complete 3–6 months of shop training prior to field dispatch.
• Valid Driver’s License with an acceptable driving record.

Responsibilities

• Build and wire industrial control panels from electrical schematics, layout prints, and BOMs.
• Mount DIN rail, wire duct, circuit breakers, contactors, relays, power supplies, VFDs, and PLCs.
• Route, crimp, terminate, and label wiring to UL 508A standards.
• Perform point-to-point continuity checks, power testing, and electrical troubleshooting prior to shipment.
• Phase 2: Measure, cut, thread, and bend EMT and Rigid conduit; pull wire and terminate power and low-voltage circuits.
• Support equipment startups, perform PLC I/O checkouts, and diagnose field wiring faults.

Skills

Schematic reading

Conduit bending

Electrical panel building

Electrical wiring

Electrical testing

DMM / Megger use

Tools

Digital multimeter (DMM)

Megohmmeter

Conduit bending tools

Hand tools

Power tools

Job description

Electrical Panel Builder & Field TechnicianLocation: Morrisville, NC (On-site shop with local field dispatch)Pay: $25.00 – $30.00 per hour (Based on Experience)Job Type: Full-timeSchedule: Monday – Friday, 8:00 AM – 5:00 PM (1st Shift)Overtime: Available / as needed based on project workloadWhy Apply?Structured Training: Comprehensive 3 to 6 months of hands-on shop training before transitioning to field service.Consistent Schedule: Reliable Monday–Friday day shift with overtime opportunities.Balanced Work: Clean shop assembly environment paired with dynamic field commissioning.Position OverviewWe are hiring an Electrical Panel Builder & Field Technician in Morrisville, NC. You will start with 3 to 6 months in the shop mastering our control panel builds, wiring standards, and testing procedures. Once fully trained, you will split time between shop builds and field installations, conduit runs, and machine startups at customer sites.What You Will Do Phase 1: Shop Assembly & Training (First 3–6 Months)Build and wire industrial control panels from electrical schematics, layout prints, and BOMs.Mount DIN rail, wire duct, circuit breakers, contactors, relays, power supplies, VFDs, and PLCs.Route, crimp, terminate, and label wiring to UL 508A standards.Perform point-to-point continuity checks, power testing, and electrical troubleshooting prior to shipment.Phase 2: Field Installations & Startups (Post-Training)Measure, cut, thread, and bend EMT and Rigid conduit (hand, mechanical, hydraulic).Pull wire, set junction boxes, and terminate power (480VAC / 240VAC / 120VAC 3-Phase) and low-voltage control circuits (24VDC, 4–20mA analog loops, sensor wiring).Support equipment startups, perform PLC I/O checkouts, and diagnose field wiring faults.Qualifications & Requirements1+ years of hands-on experience in electrical control panel building or electrical work.Proven ability to read and interpret electrical schematics and wiring diagrams independently.Practical experience bending conduit (EMT/Rigid) and pulling wire. (preferred)Solid understanding of 480V 3-phase power and 24VDC control circuits.Proficiency using digital multimeters, megohmmeters (meggers), and hand/power tools.Willingness to complete 3–6 months of shop training prior to field dispatch.Flexibility to work overtime as needed based on workload.Valid Driver’s License with an acceptable driving record.How to ApplyClick Apply Now with an updated resume detailing your panel assembly, conduit, and electrical experience.#AIS12