Crane Operator

Acadian Contractors, Inc.; Brownsville (TX); On-site; USD 50,000 - 75,000; Full time

Job summary

Acadian Contractors, Inc. is seeking an experienced Crane Operator to safely operate mobile cranes on construction sites and offsite locations. You will perform inspections, verify setup conditions, coordinate lifts with riggers and signalers, and maintain logs.

You hold an OSHA-certified crane license, have 3+ years of experience, and can work with strict safety standards. The role emphasizes adherence to load charts, proper use of safety devices, and effective communication with the crew.

Qualifications

• Current crane operator certification from an OSHA-recognized organization.
• Must complete and maintain ACI’s operator evaluation for each equipment type.
• Minimum 3 years mobile crane operating experience.
• Thorough knowledge of load charts, crane configurations, and net capacity.
• Valid driver’s license; CDL preferred for over-the-road movement.
• U.S. citizenship may be required for project assignments.

Responsibilities

• Perform and document crane inspections per OSHA and manufacturer requirements.
• Verify crane setup and ground conditions before operations.
• Verify operational aids are functional and use alternative measures if needed.
• Review lift plans, loads, rigging, and crane configuration before each lift.
• Operate within load chart capacity and follow safety devices.
• Use hand signals or radio with qualified signal person; stop if signals are unclear.

Skills

Crane certification

Operator evaluation

Crane experience

Load charts

Rigging knowledge

OSHA regulations

Driver's license

Citizenship requirement

Job description

Job Summary

The

Acadian Contractors, Inc. maintains a continuing policy of non-discrimination in employment. It is our policy to provide equal opportunity to protected veterans in all phases of the employment process and in compliance with applicable federal, state, and local laws and regulations. This policy of non-discrimination shall include, but not be limited to, the following employment decisions and practices: hiring; promotions; demotions or transfers; layoffs; recalls; terminations; rates of pay or other forms of compensation; selection for training, including apprenticeship; and recruitment or recruitment advertising. All employment decisions are based only on valid job requirements.

• Perform and document daily (shift) and monthly crane inspections per OSHA 1926.1412 and manufacturer requirements; remove deficient equipment from service and report to the foreman
• Verify crane setup before operations: ground conditions and compaction, matting/cribbing, outrigger or crawler position, levelness, swing radius protection, and counterweight configuration
• Verify operational aids (load moment indicator, anti-two-block, boom angle/length indicators) are functional before lifting; follow required alternative measures when an aid is inoperative
• Review lift plans, load weights, rigging arrangements, and crane configuration before each lift; participate in critical lift planning and pre-lift meetings
• Operate the crane within load chart capacity for the configuration in use; never exceed rated capacity or bypass safety devices
• Execute lifts using standard hand signals or radio communication with a qualified signal person; stop operations any time signals are unclear or communication is lost
• Maintain required clearances from energized power lines per OSHA 1926.1407-1411 and follow encroachment prevention measures
• Perform lifting, setting, swinging, pick-and-carry, and pile driving support operations as qualified and directed
• Monitor wind, weather, and site conditions; suspend operations when conditions exceed safe operating limits
• Stop or refuse any lift the operator judges unsafe; the operator’s authority over the crane function is absolute
• Participate in assembly/disassembly of boom sections and crane components under the direction of the A/D director as qualified
• Coordinate crane travel, positioning, and securement on site; verify travel paths, overhead clearances, and tail swing areas are controlled
• Support loading, unloading, and securement of the crane for transport between job sites
• Perform operator-level maintenance (fluids, greasing, wire rope inspection support) and report maintenance needs; maintain accurate operator logs and inspection records
• Direct riggers and crew members interfacing with the lift as it relates to crane safety
• Maintain cleanliness and organization of the crane, cab, and work area throughout the shift
• Participate in daily JSA meetings and follow all OSHA/company safety requirements
• Additional duties as directed by Supervisor

Location:

Varies

Employment Type:

Full-time

Job Summary

The Crane Operator safely operates mobile cranes (lattice boom crawler/truck and telescopic boom) on construction sites and offsite field locations, performing lifting, setting, and pile driving support operations for structural, piping, pipeline, and facility construction scopes. This role is accountable for operating within the crane’s load chart and configuration limits, performing and documenting required inspections, verifying setup and ground conditions, and coordinating every lift with riggers, signal persons, and the crew. The Crane Operator holds absolute authority to stop or refuse any lift they judge unsafe, takes direction from the foreman or lift supervisor for work sequencing, and is accountable for the condition of assigned equipment. This position is non-exempt (Hourly).

Key Responsibilities

• Perform and document daily (shift) and monthly crane inspections per OSHA 1926.1412 and manufacturer requirements; remove deficient equipment from service and report to the foreman
• Verify crane setup before operations: ground conditions and compaction, matting/cribbing, outrigger or crawler position, levelness, swing radius protection, and counterweight configuration
• Verify operational aids (load moment indicator, anti-two-block, boom angle/length indicators) are functional before lifting; follow required alternative measures when an aid is inoperative
• Review lift plans, load weights, rigging arrangements, and crane configuration before each lift; participate in critical lift planning and pre-lift meetings
• Operate the crane within load chart capacity for the configuration in use; never exceed rated capacity or bypass safety devices
• Execute lifts using standard hand signals or radio communication with a qualified signal person; stop operations any time signals are unclear or communication is lost
• Maintain required clearances from energized power lines per OSHA 1926.1407-1411 and follow encroachment prevention measures
• Perform lifting, setting, swinging, pick-and-carry, and pile driving support operations as qualified and directed
• Monitor wind, weather, and site conditions; suspend operations when conditions exceed safe operating limits
• Stop or refuse any lift the operator judges unsafe; the operator’s authority over the crane function is absolute
• Participate in assembly/disassembly of boom sections and crane components under the direction of the A/D director as qualified
• Coordinate crane travel, positioning, and securement on site; verify travel paths, overhead clearances, and tail swing areas are controlled
• Support loading, unloading, and securement of the crane for transport between job sites
• Perform operator-level maintenance (fluids, greasing, wire rope inspection support) and report maintenance needs; maintain accurate operator logs and inspection records
• Direct riggers and crew members interfacing with the lift as it relates to crane safety
• Maintain cleanliness and organization of the crane, cab, and work area throughout the shift
• Participate in daily JSA meetings and follow all OSHA/company safety requirements
• Additional duties as directed by Supervisor

Qualifications And Experience

• Current crane operator certification from an OSHA-recognized accredited testing organization (NCCCO preferred) in the applicable crane type(s) — Lattice Boom Crane (LAT/LBC/LBT) and/or Telescopic Boom (TLL swing cab, TSS fixed cab) — required when designated by work scope, client, or regulation, per OSHA 29 CFR 1926.1427
• Must complete and maintain ACI’s documented operator evaluation for each equipment type and configuration assigned, per OSHA 29 CFR 1926.1427(f)
• Minimum 3 years of mobile crane operating experience in industrial or heavy construction preferred
• Thorough knowledge of load charts, crane configurations, quadrants of operation, and net capacity calculations
• Working knowledge of rigging hardware, sling capacities, standard hand and radio signals, and OSHA 1926 Subpart CC requirements including power line clearances
• Ability to pass the physical/medical requirements applicable to certified crane operators, including vision and hearing standards
• Valid driver’s license required; CDL preferred for over-the-road movement of truck-mounted cranes
• Due to the contractual/customer requirements applicable to this project, this position is limited to U.S. citizens. Candidates must be able to provide documentation verifying U.S. citizenship if required for project assignments.
• Ability to work at heights and in extreme temperatures
• Must be able to work overtime, weekends, and travel as required to offsite project locations

Key Competencies

• Proficiency in reading and interpreting engineering drawings and welding symbols.
• Knowledge of welding processes and material properties for carbon, alloy, and stainless steel.
• Strong attention to detail and commitment to producing high-quality work.
• Effective communication and teamwork skills.
• Commitment to safety standards and proper equipment handling.

HSE Responsibilities

• Embrace, lead and demonstrate “Acadian F.I.R.S.T.” – Vision & Mission Statement as fundamental core values.
• Demonstrate visible leadership and support the proactive safety processes (JSA, Time Out & TEAM BBS Observations) to achieve an incident free workplace and advance our safety culture.
• Adhere to all “Health, Safety & Environmental (HSE) Management Systems” policies, procedures, safe work & best practices guidance as well as regulatory and client site specific policies and procedures.
• Leaders must make a personal commitment and be accountability for the HSE results, driving towards achievement of HSE goals. These goals must be clearly communicated through their direct reports, with clear expectations while coaching, mentoring and empowering others to achieve the desired results.
• Conduct periodic quality assessments of HSE processes to aid in their own coaching and mentoring of others demonstrating ownership of the results for such process implementation