Automation Controls Engineer II - Relocation Assistance Eligible

Pmdautomation; Town of Victor (NY); On-site; USD 90,000 - 130,000; Full time

Benefits offered by this job

Relocation assistance may be available

Job summary

PMDautomation is seeking a Controls Engineer II in the United States to design controls hardware, program and debug turnkey automation equipment, and lead site installations.

Responsibilities include translating mechanical designs into control schematics, drafting with AutoCAD Electrical, developing symbols, and coordinating with build and software teams through the project lifecycle.

Qualifications

• BS in EE, EET, Mechatronics, or related engineering field.
• Experience reviewing customer requirements and standards compliance.
• Ability to read, analyze, and interpret general technical procedures.

Responsibilities

• Work independently on medium-sized or average complexity projects and/or under direction of more senior engineers on portions of larger or more complex projects.
• Review customer requirements, PMD proposal, PMD cost estimate, and Federal, State, & Local requirements.
• Translate device list provided by Mechanical Engineering into Controls Hardware design elements.
• Utilize AutoCad Electrical for drafting and develop new symbols & circuits as necessary.
• Control hardware design, including AC/DC power schematics and enclosure layouts.
• Assist Controls Build Technicians, Controls Software Engineers, and Controls Engineers with electrical and fluid power debug.
• Update design as required throughout the project life cycle.
• Create custom device driver code and program controller sequences from timing charts.

Education

BS in EE, EET, Mechatronics, or related engineering field; or demonstrated equivalent experience

Tools

AutoCad Electrical

NFP79

UL508a

CE

CSA standards

Power calculations

Enclosure Heat calculations

SCCR calculations

Fluid Power flow calculations

SISTEMA safety calculations

Job description

Description

Relocation Assistance may be available for qualified candidates.

JOB SUMMARY

The Controls Engineer II is responsible for providing controls hardware design, programming, debug, and site-installation of turnkey custom automation equipment.

ESSENTIAL FUNCTIONS

• Work independently on medium sized or average complexity projects and/or under direction of more senior engineers on portions of larger or more complex projects.
• Review customer requirements, PMD proposal, PMD cost estimate, and Federal, State, & Local requirements.
• In advance of completed Mechanical Engineering design, attend Mechanical Design Reviews to understand machine functionality, suggest concepts & componentry to meet functional & safety requirements, and incorporate associated Controls Hardware design elements into the Controls Hardware design.
• Translate device list provided by Mechanical Engineering into Controls Hardware design elements.
• Utilize AutoCad Electrical for drafting.
• Use provided symbols & circuits.
• Develop new symbols & circuits as necessary.
• Controls Hardware Design
• AC Power schematics
• DC Power schematics
• Safety schematics
• Servo/Stepper schematics
• Industrial Network schematics
• Device schematics
• Testers, Transducers, Laser Markers, Welders, Robots, etc.
• I/O schematics
• Control Enclosure layouts
• Control Panel layouts
• Fluid Power Supply schematics
• Fluid Power Control schematics
• Bill of Materials
• Interact with Controls Build personnel to answer questions.
• Assist Controls Build Technicians, Controls Software Engineers, and Controls Engineers with electrical and fluid power debug.
• Update design as required throughout the project life cycle.
• Use provided standard code and device drivers, or use end-customer provided code and/or formats to create custom control & HMI programs.
• Create custom device driver code.
• Using control schematics, enter I/O into controller programs.
• Using timing chart provided by Mechanical Engineering, program intended sequences into controller programs.
• Download completed programs.
• Commission control hardware.
• Debug control hardware for out-of-box failures, intended design, and correct wiring/plumbing.
• Debug control software, including all intended sequences, modes of operation, special functions, fault detection, fault recovery, tooling return, and interface.
• Participate in Factory Acceptance Test at PMD.
• Participate in Site Acceptance Test at end-customer’s facility

OTHER DUTIES

• Maintain a clean and orderly work area.
• Observe safety procedures.
• Any other task assigned by management within scope of position, federal and state regulations.

Requirements

EDUCATION

• BS in EE, EET, Mechatronics, related engineering field; or demonstrated equivalent experience.

EXPERIENCE (5-10 years)

with 4 or more of the following Hardware Design skills:

• AutoCad Electrical
• NFP79, UL508a, CE, CSA standards
• Power calculations (AC 3phase, AC 1phase, DC 5-90V, Transformers)
• Enclosure Heat calculations
• SCCR calculations
• Fluid Power flow calculationsSISTEMA safety calculations

and 3 or more of the following Programming skills:

• PLC Programming (Rockwell, Siemens, and/or Omron)
• HMI Programming (Rockwell, Siemens, and/or Omron)
• Robot Programming (Fanuc, ABB, Epson, Staubli, and/or Kuka)
• Vision Systems (Cognex, Keyence, Matrox, and/or Teledyne Dalsa)
• Industrial Protocols (Ethernet/IP, ProfiNet, EtherCat, and/or IOLink)

KNOWLEDGE, SKILLS & ABILITIES

• Effective verbal and written communication.
• Ability to read, analyze, and interpret general technical procedures.
• Ability to work in decimal, octal hexadecimal, and binary numbering systems.
• Ability to apply concepts of basic algebra and geometry and to calculate scaling factors, proportions, percentages, rates, and ratios.
• Organized
• Detail oriented
• Ability to work independently or as part of a team
• Ability to take direction
• Creative/Innovative
• Time management skills

PHYSICAL DEMANDS & WORK ENVIRONMENT

The physical demands described here are representative of those that must be met by an employee to successfully perform the essential functions of this job. Reasonable accommodations may be made to enable individuals with disabilities to perform the essential functions.

• Regularly required to sit; use hands to handle or feel; reach with hands and arms; talk or hear; and smell.
• Occasionally required to stand, walk, push, pull, lift, stoop, kneel, crouch and crawl.
• Specific vision abilities include close vision, distance vision, color vision, peripheral vision, depth perception, and ability to adjust focus.
• Work environment is primarily performed indoors; partially around moving mechanical parts at a moderate noise level.
• Wear safety equipment, including proper PPE.