Machine Operator (Stator & Rotor)

NOV; Abu Dhabi; Sur place; AED 66 960 - 100 440; Plein temps

Résumé du poste

NOV is seeking a Machine Operator to manufacture Stators and Rotors for oilfield directional drilling. You will follow SOPs, perform quality checks, and assist in machine maintenance and repair tasks on the shop floor.

The role requires reading drawings, using measuring tools, and applying basic math. English communication and adherence to HSE policies are essential for daily operations.

Qualifications

• High School Diploma or equivalent with knowledge in basic math.
• Ability to read and understand engineering drawings.
• Basic math and measurement skills required.

Responsabilités

• Manufacture stators and rotors for oilfield directional drilling.
• Follow procedures related to stator and rotor manufacturing process.
• Review necessary process frequency to be fluent and aware of critical parameters.
• Verify quality checks at each manufacturing step prior to next process.
• Support continual improvement and problem-solving initiatives.
• Follow SOPs and perform tasks per Job Hazard Analysis.
• Operate overhead cranes for movement of parts or products.
• Report abnormalities or variations observed in the manufacturing process.
• Ensure tools, gauges and equipment are maintained properly.
• Document and maintain checklists, paper routers, or ERP entries.
• Assist in repair work of machines or areas in the facility.
• Handle products, tubes & core at elevated temperatures with safety procedures.
• Follow 5S housekeeping requirements.
• Suggest improvements, risks, safety concerns and good practices.
• Comply with NOV HSE procedures and maintain logs.
• Observe HSE regulations and promote safe working practices.

Connaissances

Measuring tools

Drawings

English communication

Pneumatic systems

Hydraulic systems

Power tools

Formation

High School Diploma

Description du poste

Job Description

Job Summary

Machine Operator responsible for the manufacturing of Power Section (Stator & Rotor) by following procedures and SOP

Responsibilities

• Manufacturing Stators and Rotors for usage in oilfield directional drilling
• Follow procedures related to stator and rotor manufacturing process
• Review of the necessary manufacturing procedures frequency to be fluent and aware of the critical parameters related to the process
• Verify quality control checks at each manufacturing process, prior to planning or transferring the job to the next process of manufacturing
• Support and participate in the Organizations Continual Improvement program and any problem-solving initiatives
• Follow the operating procedures (SOP) and perform the task based on the Job Hazard analysis performed
• Operation of overhead cranes in the movement of parts or products
• Report any abnormalities or variations observed in the manufacturing process to the concerned parties
• Ensure the tools, gauges and equipment’s used in manufacturing are maintained properly
• Document and maintain checklist, paper routers, or any ERP system that are in place
• Assist and support in the repair work of any machine or areas in the facility
• Handling of products, tubes & core at elevated temperatures by following the necessary safety procedures
• Follow the house keeping as per the 5S requirements
• Suggest or raise observation on any improvements, risk, safety concerns and good practices
• Ensure to comply with all NOV HSE procedures and policies and maintain relevant HSE logs
• Observe HSE regulations, encourages safe working practices, corrects obvious hazards immediately or reports them to the proper personnel

Behavioral Skills/Competencies & Experience Required

• Perform daily operator checklist of machines
• Capture/measure necessary process parameters and record the readings
• Ensure controlled use of elastomer & chemicals issued to shop floor
• Check the stator or rotor prior to starting any process and report if in doubt
• Ensure the stator/rotor is processed to the next step only after complete review of task performed
• Ensure machines are running as per the requirement
• Operate Boiler, Generator, Air compressors, Forklift (License/Certification required) when needs/advised
• Assist maintenance technicians when critical machine breakdowns are been attended
• Provide training to any new hire / operators that are under the certification program
• Other duties, as assigned by the supervisor

Qualifications (Education/No. of Years of Experience)

• High School Diploma or equivalent with knowledge in basic math

Skills, Training, Special Knowledge, And/or Language Skills

• Knowledge of the proper use of measuring tools/gauge and tools
• Understand routers, drawings and procedures
• Able to communicate in English (both writing and orally)
• Understanding of pneumatic, hydraulic, basic electrical systems and with mechanical aptitude. Experience in safe use of power tools used in Manufacturing Industries

Quality Assurance

• Ability to understand basic engineering drawings
• Ability to present and explain basic technical information to diverse audience
• Ability to document, store and retrieve information as per basic QMS

About Us

Every day, the oil and gas industry’s best minds put more than 150 years of experience to work to help our customers achieve lasting success.

We Power the Industry that Powers the World

Throughout every region in the world and across every area of drilling and production, our family of companies has provided the technical expertise, advanced equipment, and operational support necessary for success—now and in the future.

Global Family

We are a global family of thousands of individuals, working as one team to create a lasting impact for ourselves, our customers, and the communities where we live and work.

Purposeful Innovation

Through purposeful business innovation, product creation, and service delivery, we are driven to power the industry that powers the world better.

Service Above All

This drives us to anticipate our customers’ needs and work with them to deliver the finest products and services on time and on budget.