Visual Dimensional Inspector - Swing Shift

Precision Castparts; Ogden (UT); On-site; USD 36,000 - 54,000; Full time

Job summary

Precision Castparts Corp. is seeking a Visual and Dimensional Inspector in Ogden, Utah. You will inspect parts visually and dimensionally, using micrometers, calipers, and fixtures to ensure conformance to blueprints and tech cards.

You will mark non-conforming areas and collaborate with engineering to resolve issues. Qualifications include a high school diploma or GED and 1–3 years in manufacturing inspection, preferably aerospace.

Qualifications

• High school diploma or GED preferred.
• 1–3 years of visual and dimensional inspection experience in manufacturing, aerospace preferred.
• Experience reading and interpreting blueprints and tech cards.

Responsibilities

• Identify surface defects by reviewing tech cards, techniques, and routers.
• Visually inspect parts at multiple process points for defects.
• Ensure dimensional integrity using templates and measuring devices.
• Mark castings that need rework to meet specs.
• Enter dimensional data into computer systems for SPC charts.
• Collaborate with engineering and other departments to resolve non-conformances.
• Prepare reports on quality issues as needed.

Skills

Visual inspection

Dimensional inspection

Reading blueprints

Measurement tools

Team communication

Education

High school diploma or GED

Tools

Micrometers

Height gauges

Calipers

Fixtures

Job description

Position Summary

To visually and dimensionally inspect parts to assure compliance to customer specifications and to assure that only necessary reworking of parts is performed.

Principle Duties And Responsibilities

• Identifies surface defects in parts by reviewing tech cards, techniques, and routers.
• Utilizes fixtures as necessary.
• Visually inspects parts at multiple points in the process for defects.
• Uses a variety of hand tools to assist in visual inspection.
• Assures dimensional integrity by inspecting castings for conformance to blueprint, technique, and tech card specifications using templates, micrometers, height gauges, calipers, fixtures, and other dimensional measuring devices.
• Marks castings to identify areas needing rework in order to meet dimensional specifications.
• Works regularly with other departments.
• Works with engineering to establish and evaluate inspection techniques and identify and resolve problems of non-conformance to specifications.
• Enters weld mapping and dimensional data into computer systems for use by engineering and SPC charting.
• Prepares reports and information on quality issues as needed.
• Performs other duties as assigned.

Minimum Job Requirements

• Ability to complete the PCC OGDEN Visual Dimension certification requirements.
• Able to read and comprehend English.
• Able to add, subtract, multiply, and divide whole and decimal numbers up to 4 decimal places.
• Able to lift and carry up to 25 lbs. unaided regularly.
• Able to communicate effectively with co-workers.
• Able to read, write, and comprehend simple instructions, short correspondence, and memos. (Techniques, routers, weld maps, log sheets.)
• Able to solve practical problems and deal with a variety of concrete variables in situations where only limited standardization exists.
• Able to interpret a variety of instructions furnished in written, oral, diagram, or schedule form.
• Near vision requirements are Jaeger J1 in one eye, at no less than 12 inches; or equivalent, or Jaeger J2 in one eye, at no less than 16 inches.
• Complies with company and departmental policies and procedures, including company’s attendance policy.
• Able to meet individual productivity requirements and work in a production environment.

Normal Working Conditions

• Works under general direction and infrequent supervision, planning details of procedure and methods to attain definite objectives. Makes decision within broad limitations of policies and within accepted standards.
• Environmental conditions encountered continuously include working near moving mechanical parts, fumes or airborne particles, and vibration.
• Typical noise environment for the work environment of this job is Loud Noise. (Appropriate ear protection is required.)
• Continuous required physical demands include using hands to handle or feel.
• Frequent required physical demands include sitting, walking, reaching below shoulder level, and pushing or pulling.
• Occasional required physical demands include standing, reaching above shoulder level, balancing, stooping or squatting, talking and hearing.

Experience & Education

• High school diploma or GED highly preferred.
• 1- 3 years of prior visual and dimensional inspection experience within the manufacturing industry, preferably in aerospace.

Precision Castparts Corp. is an equal opportunity employer committed to recruit, hire, train, and promote in all job categories without regard to race, color, religion, sex, sexual orientation, gender identity, national origin, age, disability, veteran status or other status protected by applicable law.