Radiologic Evaluator Technical Lead LPC LSBS 072

Precision Castparts Corp.; Portland (OR); On-site; USD 90,000 - 120,000; Full time

Job summary

LPC is seeking a Radiologic Evaluator Technical Lead in Portland, Oregon, to be the on-site technical resource for daily issues from the process and inspection staff and assist with process control and cross-training.

You will drive teamwork, ensure quality requirements are followed, and coordinate with molding, tool maintenance, and engineering to improve part quality, tool use, and throughput while maintaining a safe, compliant work environment.

Qualifications

• Certification required or ability to certify within 90 days.
• TATS certification and other certifications may be required based on departmental needs.
• Willingness to adjust shift and perform various jobs to process parts.
• Ability to communicate verbally and in writing clearly.
• Ability to present shop floor results to customers and engineering.
• Incumbents with excessive absenteeism may be dismissed from lead position.

Responsibilities

• Participate in staffing projections and staff allocation.
• Handle first-line technical performance issues; communicate respectfully with staff.
• Provide fact-based input for performance reviews and measurements.
• Train employees on new skills; coach for continuous improvement.
• Coordinate resources to meet daily throughput and support other departments.
• Maintain harassment/discrimination free environment and avoid favoritism.
• Complete Hazardous Waste Management Training when required.
• Ensure quality requirements flow down through QCM and documents.
• Correct deficiencies and notify relevant parties when a process is variant.
• Facilitate technique card and router changes; assist with root cause analysis.
• Ensure team has necessary tools and documents for inspections.
• Assist with internal and external audits as focal point.
• Set up molding parameters; evaluate parameters for process improvement.
• Review tool designs with engineering for function and quality.
• Work with molding/tool engineers for tool proving and improvements.
• Open and display dies for customers/vendors; assist with tool proving.
• Interface with customers, engineering, and other departments for process walks.
• Authority to correct interpretation calls by inspectors; notify deviations.
• May be assigned to multiple work centers or departments.
• Other duties as assigned.

Skills

Team leadership

Communication

Training

Job description

Radiologic Evaluator Technical Lead LPC LSBS 072

Country United States of America

State / County Oregon

City Portland

Division Structurals

Company LPC

Function Operations

Workplace Type On-Site

Position type Full Time

Opportunity ID 24367

Job Description

MISSION:

To be the on sight technical resource for daily issues arising from the process and/or inspection staff. To assist with process control issues, and cross training.

PRINCIPAL ACCOUNTABILITIES:

A. Teamwork

• Participates in staffing projections.
• Handles first line technical performance issues. Communicates with employees in a respectful manner regarding workmanship issues. Notifies supervision when further action is required to improve technical performance.
• Gives fact-based input from the technical aspect for performance reviews and measurements.
• Trains employees on new skills and works with employees to improve technical performance to satisfactory levels or maintain satisfactory performance.
• Provides feedback and coaching for continuous improvement of the inspection personnel.
• Coordinates resources to move from one team to help another when necessary to meet daily thru-put and support outside departments.
• Is sensitive to and proactively supports the maintenance of a harassment/discrimination free environment.
• Avoids favoritism or the perception of favoritism.
• May be required to complete Hazardous Waste Management Training.

B. Process Control

• Ensures that the quality requirements flowed down through the QCM and related documents are followed.
• Corrects deficiencies and notifies appropriate party/parties when a process is variant.
• Facilitates technique card and router changes.
• Participates in root cause analysis for variant conditions.
• Ensure the team has the necessary tools and documents to perform the required inspections.
• Assists with auditing. Both as an auditor and as the focal point for the team during external audits,

C. Molding

• Setup molding parameters on new tools.
• Evaluate / update current molding parameters for process improvement.
• Review tool shots for part quality (provide recommendations for part quality improvements).
• Review tool designs with engineering for functionality and part quality.
• Work with molding / tool engineers for tool proving (provide feedback).
• Work directly with process control for tool improvements.

D. Tool Maintenance

• Clean dies.
• Remove rust.
• Lube & grease dies.
• Polish out minor nicks and dings (scotch bright).
• Replace dowel / leader pins (as needed – can be contracted outside).
• Replace sintered vents (as needed – can be contracted outside).
• Repair airboxes including "O" rings and pins (as needed – can be contracted outside).
• Evaluate wax dies for damage / and functionalit.y
• Open and display dies for customers / vendors.
• Work with molding / tool engineers for tool proving (provide feedback).

E. Other

• Interfaces with customers, engineering, and other departments to give process walks and presentations.
• Has the authority as granted by the responsible level 3 to correct any interpretation calls by the other department inspectors.
• Contacts appropriate resources if any employee may not be fit for duty. Addresses the issue promptly.
• Assures compliance with safe work habits and maintenance of proper housekeeping procedures
• Assures compliance with company policies and procedures and promptly notifies supervision of deviations.
• Other duties as assigned.
• May be assigned to multiple work centers or departments.

QUALIFICATIONS:

• Certification in the required based on departmental needs. Or ability to certify within 90 days required. If employee cannot certify within 90 days then employee is disqualified
• from position.
• TATS certification and other certifications will be required based on departmental needs.
• Incumbent must be willing, as required by team and production needs to:
  • Adjust shift
  • Perform various jobs required to process parts
  • Interface with other teams and support areas.
• Ability to communicate verbally and in writing. Instructions must be clear and unambiguous; consistently assures directions are clearly understood resulting in work that rarely, if ever, needs to be redone due to the quality of communication.
• Ability to make "shop floor" presentations to customers, engineering, and other departments as required or requested.
• See department qualification which may or may not be shift specific
• Incumbents who are regularly unavailable through excessive absenteeism (excluding approved leaves) or are deemed incapable of performing the required job functions of a Lead, may be dismissed from their lead position without use of disciplinary action.

All qualified applicants will receive consideration for employment without regard to race, color, religion, sex, sexual orientation, gender identity, national origin, disability, or status as a protected veteran.

This position requires use of information or access to production processes subject to national security controls under U.S. export control laws and regulations (including, but not limited to the International Traffic in Arms Regulations (ITAR) and the Export Administration Regulations (EAR)). To comply with those regulations, this position may require applicants to be U.S. Persons (i.e., U.S. citizens, U.S. lawful permanent residents, protected individuals as defined by 8 U.S.C. 1324b(a)(3)), or eligible to obtain the required export authorizations from the U.S. Department of State or the U.S. Department of Commerce.

Company Profile

With more than 120 operations and approximately 20,000 employees worldwide, Precision Castparts Corp. is the market leader in manufacturing large, complex structural investment castings, airfoil castings, forged components, aerostructures and highly engineered, critical fasteners for aerospace applications. In addition, we are the leading producer of airfoil castings for the industrial gas turbine market. We also manufacture extruded seamless pipe, fittings, and forgings for power generation and oil & gas applications; commercial and military airframe aerostructures; and metal alloys and other materials for the casting and forging industries. With such critical applications, we insist on quality and dependability – not just in the materials and products we make, but in the people we recruit.

PCC is relentless in its dedication to being a high-quality, low-cost and on-time producer; delivering the highest value to its customers while continually pursuing strategic, profitable growth.

In 2016, Berkshire Hathaway, led by Chairman and CEO Warren E. Buffett, acquired Precision Castparts Corp.

Precision Castparts Corp. and its affiliates do not accept unsolicited resumes from search firms or employment agencies. Unsolicited resumes will become the property of Precision Castparts Corp & its affiliates, and no fee will be paid.

We are constantly searching for the best talent and offer excellent development programs for recent graduates as well as meaningful work experience for those still studying.