Low Pressure Braider Operator - 3rd Shift (11:30 PM - 7:30 AM)

Parker Hannifin; Mansfield (TX); Presencial; USD 36.000 - 52.000; Jornada completa

Descripción de la vacante

Parker Hannifin in Mansfield, TX is seeking a production operator to operate NEB, OMA and/or TMW braiders and monitor product quality.

You will pull tooling, set up machines, inspect tooling, record measurements, and follow 5S and safety guidelines while maintaining a clean, safe work area.

Formación

• High School diploma or GED required.
• Production work preferred but not required.
• Good verbal and interpersonal communication skills.
• Basic knowledge and use of hand tools.
• Sound decision making skills.
• Good math, reading, writing skills.
• Demonstrated mechanical aptitude.
• Strong trouble shooting skills.
• Ability to work well in a team environment.

Responsabilidades

• Pull tooling and materials according to manufacturing specifications for applicable machine(s).
• Inspect tooling before using and track material used in WW3 system and Braider Logs.
• Set up machines according to manufacturing specifications and mark defects/new preforms with tape color.
• Measure and record OD and pitch on Hose Process Chart (SPC).
• Run braided hose through wash tank and stage in hose coiling area for inspection.
• Maintain clean and orderly work area and follow 5S practices.
• Follow safety regulations and quality guidelines; report production issues.
• Perform work of an equal or lower classification.

Conocimientos

Good verbal and interpersonal comms

Hand tools use

Decision making

Math/Reading/Writing

Mechanical aptitude

Troubleshooting

Attention to detail

Teamwork

Educación

High School diploma or GED

Herramientas

Calipers

Micrometers

Pi tape

NEB braiders

TMW braiders

OMA braiders

Descripción del empleo

Position Summary

Operate either the NEB, OMA and/or TMW 24/36 braiders and monitor for proper product quality

ESSENTIAL FUNCTIONS

1. Pull tooling and materials according to manufacturing specifications for applicable machine(s), such as springs, braid rings, tube guides, wound bobbin, core tube, etc.
2. Inspect tooling before using and track material used in WW3 system and Braider Logs
3. Set up applicable machine(s) according to manufacturing specifications (braid ring height, install tube guide, change deck/puller gear, unload/load carriers, unload/load bobbins, etc.) and mark defects/new preforms with the correct tape color
4. Measure and record OD and pitch on Hose Process Chart (SPC)
5. Run braided hose through wash tank and stage in hose coiling area for inspection
6. Maintain work area in clean and orderly fashion, follow 5s practices
7. Know and practice all safety regulations and quality guidelines
8. Report production issues to Direct Lead
9. Perform work of an equal or lower classification

DEPARTMENT SPECIFIC/NON-ESSENTIAL FUNCTIONS

1. Work safely in accordance with regulations, standards, and procedures, and in a manner that eliminates unreasonable risk to health and the environment.Notify management of unsafe conditions or practices, unlawful activities and activities which present unreasonable health and/or environmental risk.Report all safety and/or environmental incidents to management immediately.
2. Prevent excess waste of product and/or components by operating the equipment in an efficient manner.
3. Participate in peer-based teams (i.e., Natural High Performance Teams), and work with groups to initiate and implement programs such as Lean Manufacturing and 5-S.
4. Other duties may be assigned at a later time.

MINIMUM REQUIREMENTS

Education required: High School diploma or GED

Experience: Production work preferred but not required

Preferred Skills/Qualifications:

1. Good verbal and interpersonal communication skills
2. Basic knowledge and use of hand tools
3. Sound decision making skills
4. Good math, reading, writing skills
5. Demonstrated mechanical aptitude
6. Strong trouble shooting skills
7. Be able to exercise continuous mental, visual, and audio attention
8. Ability to work well in a team environment

Skills/Competencies:

1.Basic computer skills

2.Ability to monitor machine sounds to identify and diagnose changes inorder to take appropriate action.

3.Vision: Near acuity and accommodation for reading information to perform job tasks.

4.Requires constant alertness to surroundings and product quality with attention to detail.

5. Must be able to read work orders and interpret manufacturing specifications.

6. Ability to use and interpret measuring instruments (i.e. calipers, micrometers, pi tape, etc.)

7. Must be able to demonstrate ability to operate department equipment (i.e. NEB braiders, TMW, OMA braiders, etc.)

Physical Requirements:

None at All (0%)

Occasional (1-33%)

Frequent (34-66%)

Continuous (67-100%)

Lift/Carry Up to 10 lbs X

11-20 lbs X

21-30 lbs X

Bending X

Twist/Turn X

Reach Below Knee X

Push/Pull X

Squat/Kneel X

Stand/Walk X

Sit X

Lifting Above Shoulders X

Assessment: Employee must pass Pre-employment screening

ORGANIZATIONAL RELATIONSHIPS/SCOPE

• Report directly to Value Stream Team Leader
• Work closely with Maintenance to resolve issues with the equipment

WORKING CONDITIONS

The employee may be subject to:

• High noise levels from operating machines and equipment.
• Physical hazards from operating machines

1. Work in areas where safety equipment will be required (steel toe shoes, eye protection, hearing protection)
2. Standing is required for extended periods of time.Walking, pushing, pulling, reaching, bending, turning, twisting, squatting, and lifting is performed on a regular basis
3. Requires high degree of manual dexterity, which could be performed under restrictive conditions
4. Requires flexible hours and short notice for overtime.

The employee may be required to follow other job-related instructions and to perform other job-related duties as requested, subject to all applicable state and federal laws.

Parker Hannifin

Parker Hannifin is a Fortune 250 global leader in motion and control technologies. For more than a century, we’ve enabled engineering breakthroughs that make energy cleaner, transportation safer, medical treatments more effective, and manufacturing more efficient.

With empowered team members in more than 40 countries, Parker serves customers across aerospace & defense, energy, HVAC & refrigeration, in-plant & industrial equipment, off-highway and transportation.

Our scale is global, but our purpose is personal. We enable breakthroughs that improve lives, strengthen communities and create a brighter future.

Our Purpose — Enabling Engineering Breakthroughs that Lead to a Better Tomorrow — comes to life through our people-first culture where teamwork drives performance, inclusion fuels innovation and growth is encouraged. This environment fosters collaboration and empowers team members from engineering and manufacturing to finance, supply chain, human resources, information technology and beyond.

By combining deep expertise with an entrepreneurial spirit, we help customers succeed in markets that demand performance, reliability, and sustainability.

As we look to the future, Parker is advancing initiatives in energy efficiency and sustainability while developing the next generation of talent and leaders to engineer a better tomorrow.

Equal Employment Opportunity

Parker is an Equal Opportunity and Affrimative Action Employer. Parker is committed to ensuring equal employment opportunities for all job applicants and employees. Employment decisions are based upon job related reasons regardless of race, ethnicity, color, religion, sex, sexual orientation, age, national origin, disability, gender identity, genetic information, veteran status, or any other status protected by law. However, U.S. Citizenship, Permanent Residency or other appropriate status is required for certain positions, in accord with U.S. import & export regulations.(“Minority / Female / Disability / Veteran / VEVRAA Federal Contractor”)

If you would like more information about Equal Employment Opportunity as an applicant under the law, please go to Employees & Job Applicants | U.S. Equal Employment Opportunity Commission

Drug Tests

Drug-Free Workplace

In accordance with Parker’s policies and applicable state laws, Parker provides for a drug-free workplace. Therefore, all applicants seeking employment with Parker will be subject to drug testing as a condition of employment.