Experienced Marine Rigger Boat Rigging Technician

DRAGONFLY BOATWORKS LLC; Vero Beach (FL); On-site; USD 55,000 - 80,000; Full time

Job summary

Dragonfly Boatworks LLC is seeking an experienced Marine Rigger / Boat Rigging Technician to perform complete boat installations accurately, cleanly, and with limited supervision. This is not an entry-level or general labor position.

Applicants must have meaningful experience in marine rigging, boatbuilding, marine electrical work, or a closely related installation trade. We are looking for a dependable technician who understands that proper measurements, secure connections, organized routing,

Qualifications

• Demonstrated experience in marine rigging, boatbuilding, marine service, or related trade.
• Working knowledge of 12- and 24-volt marine electrical systems.
• Experience installing and troubleshooting wiring, batteries, switches, breakers, and pumps.
• Ability to read wiring diagrams and follow production specifications.
• Strong troubleshooting, attention to detail, and safe work practices.
• Ability to work independently and report to supervision as needed.
• Valid driver’s license and legal authorization to work in the United States.

Responsibilities

• Rig boats from initial installation through final testing and completion.
• Install outboard motors, steering systems, gauges, wiring, and electrical components.
• Route wiring, hoses, and control lines neatly and safely.
• Test installed systems and verify proper operation before boat leaves the department.
• Maintain a clean, organized, and safe work area and coordinate with teams to meet schedule.

Skills

Marine rigging

Boatbuilding

Electrical work

Reading wiring diagrams

Shop math

Independent work

Valid driver's license

English communication

Tools

Multimeters

Crimpers

Electrical testers

Job description

Dragonfly Boatworks is seeking an experienced Marine Rigger / Boat Rigging Technician who can perform complete boat installations accurately, cleanly, and with limited supervision.

This is not an entry-level or general labor position. Applicants must have meaningful experience in marine rigging, boatbuilding, marine electrical work, or a closely related installation trade.

We are looking for a dependable technician who understands that proper measurements, secure connections, organized routing, thorough testing, and professional workmanship are essential to building a safe and reliable boat.

Primary Responsibilities

• Rig boats from initial installation through final testing and completion
• Install outboard motors, steering systems, throttle and shift controls, gauges, wiring, batteries, pumps, switches, hardware, and accessories
• Install and connect fuel, plumbing, bilge, livewell, and electrical systems
• Work with both 12-volt and 24-volt marine electrical systems
• Route wiring, cables, hoses, and control lines neatly, securely, and safely
• Read and follow wiring diagrams, installation manuals, measurements, production specifications, and work instructions
• Diagnose and correct electrical, mechanical, installation, and fitment problems
• Test installed systems and verify proper operation before a boat leaves the department
• Identify incomplete, damaged, unsafe, or incorrectly installed components
• Complete assigned work accurately without requiring continuous supervision
• Protect finished surfaces while drilling, cutting, mounting, and installing equipment
• Maintain a clean, organized, and safe work area
• Coordinate with supervisors and other departments to complete boats on schedule

Minimum Qualifications

• Demonstrated experience in marine rigging, boatbuilding, marine service, marine electrical work, or a closely related trade
• Working knowledge of both 12-volt and 24-volt marine electrical systems
• Experience installing and troubleshooting wiring, batteries, switches, breakers, chargers, distribution panels, pumps, and related marine equipment
• Ability to identify voltage requirements and verify that components are correctly installed, connected, protected, and tested
• Experience using hand tools, cordless tools, drills, saws, crimpers, multimeters, and other installation or diagnostic equipment
• Ability to read a tape measure accurately and perform basic shop math
• Ability to make secure electrical connections using proper terminals, connectors, crimping methods, and heat shrink
• Understanding of wire routing, circuit protection, polarity, grounding, and safe battery connections
• Ability to read wiring diagrams, manufacturer instructions, and production specifications
• Strong troubleshooting and problem-solving skills
• High attention to detail and an understanding of professional fit-and-finish standards
• Ability to work independently while remaining accountable for completed work
• Reliable attendance and the ability to report to work on time
• Clear English communication skills sufficient for safety instructions, training, documentation, and teamwork
• A valid driver’s license
• Authorization to work in the United States and the ability to complete required employment verification

Preferred Experience

• Rigging a boat from an unfinished hull through final completion
• Outboard motor installation and setup
• Hydraulic and mechanical steering systems
• Throttle and shift control installation
• 12-volt and 24-volt battery banks and multi-battery systems
• Battery switches, chargers, breakers, fuses, relays, and distribution panels
• Proper wire sizing, circuit protection, terminal installation, and heat‑shrink connections
• Bilge pumps, livewell systems, fuel systems, freshwater systems, and plumbing
• Trolling motors, trim tabs, jack plates, marine electronics, lighting, and accessories
• Reading marine wiring diagrams and manufacturer installation manuals
• Using multimeters to test voltage, continuity, polarity, and electrical connections
• Troubleshooting electrical, mechanical, or installation problemsPerforming final system checks and quality‑control inspections

Quality Expectations

• Produce clean, organized, and professional installations
• Measure carefully before drilling, cutting, or mounting equipment
• Confirm voltage requirements before connecting equipment
• Keep 12-volt and 24-volt circuits properly identified and separated
• Protect finished surfaces and components while working
• Complete assignments correctly rather than relying on another employee to repair repeated mistakes
• Recognize when an installation is unsafe, incomplete, poorly routed, or below company standards
• Test completed work before considering an assignment finished
• Accept feedback, follow established procedures, and correct issues promptly
• Take responsibility for assigned work from start to finish
• Maintain consistent quality while meeting production expectations

Application Requirements

• Previous marine rigging or related installation experience
• Types of boats and systems previously worked on
• Experience with 12-volt and 24-volt marine electrical systems
• Experience with steering, controls, plumbing, batteries, pumps, wiring, and outboard installation
• Tools and diagnostic equipment they are comfortable using
• Their ability to rig and troubleshoot a boat independently

Applicants whose experience is limited to general labor, detailing, basic assembly, or assisting another rigger without independently completing installations may not meet the requirements for this position.

Final candidates may be asked to complete a practical skills evaluation involving measuring, tool use, wiring, system identification, and troubleshooting. Candidates may also be subject to lawful pre‑employment screening relevant to the duties of the position.