Electrical Manufacturing Engineer

TDW

Tulsa (OK)

On-site

USD 90,000 - 125,000

Full time

14 days+

A complete application in a minute

Tailored resume and cover letter, ready to send.

Get past ATS filters

Job summary

TDW in Tulsa, OK seeks an experienced Manufacturing/Electrical Engineer to lead production test systems, NPI collaboration, and process development for electronic assemblies. You will build and optimize procedures, support new product introductions, and drive yield improvements while troubleshooting complex electrical and firmware issues.

Ideal candidates have a bachelor's in Electrical/Mechatronics and 10+ years in electronics manufacturing, with hands-on experience in test equipment, PCB

Qualifications

  • Bachelor's degree in Electrical Engineering, Electronics Engineering, Mechatronics Engineering, or equivalent.
  • Ten or more years of experience in electronics manufacturing, manufacturing engineering, NPI, or related roles.
  • Ability to read PCB schematics, PCB layout drawings, wiring diagrams, and test procedures.
  • Experience using test and diagnostic equipment including oscilloscopes, multimeters, logic analyzers, power supplies, CAN analyzers.

Responsibilities

  • Production Test Systems: Develop, maintain, debug, and improve test programs, fixtures, and validation procedures.
  • New Product Introduction: Define manufacturing requirements, test strategies, build plans, and readiness for new products.
  • Manufacturing Process Development: Develop and improve processes; create assembly procedures and work instructions.
  • Product Build Support: Provide hands-on support during builds and ramp-up; address manufacturability and quality issues.
  • Documentation: Write and maintain work instructions, test procedures, and troubleshooting guides.
  • Production Support & Troubleshooting: Troubleshoot electrical, firmware, and test-related issues; collaborate across teams.
  • Electronics Testing and Troubleshooting: Perform board- and system-level debugging with lab equipment.
  • Yield Improvement & Failure Analysis: Analyze data, lead root cause investigations, implement corrective actions.
  • Configuration & Change Implementation: Support engineering changes and validation; maintain configuration control.
  • Supplier Support: Work with suppliers on component issues; support first article inspections and corrective actions.
  • Engineering & Manufacturing Integration: Act as the technical interface between Product Development and Manufacturing.
  • Ability to travel domestically and internationally 10-15%.

Skills

Electrical engineering fundamentals
Manufacturing process development
Root cause analysis
Cross-functional collaboration
Documentation

Education

Bachelor's degree in Electrical/Mechatronics Engineering

Tools

Oscilloscopes
Digital multimeters
Logic analyzers
Power supplies
CAN analyzers
Soldering SMT/through-hole

Job description

At TDW we put people first - that means working everyday to ensure the pipelines that run through our communities are operating safely and reliably. What sets us apart is our expertise, experience and commitment.

Each day we dedicate ourselves to treating each other, our customers and our community with care and respect.

Key Responsibilities
  • Production Test Systems: Develop, maintain, debug, and improve electronic production test programs, fixtures, and validation procedures used for day-to-day manufacturing operations.
  • New Product Introduction: Partner with Engineering, Operations, Suppliers, and Quality to define manufacturing requirements, test strategies, build plans, and production readiness activities for new product introductions.
  • Manufacturing Process Development: Develop, validate, and improve manufacturing processes for electronic assemblies and systems. Create and maintain assembly procedures, manufacturing documentation, and work instructions.
  • Product Build Support: Provide hands-on support during product builds, pilot builds, and production ramp-up activities. Identify manufacturing risks and implement solutions to improve build quality, manufacturability, and efficiency.
  • Documentation: Write and maintain manufacturing work instructions, test procedures, assembly procedures, troubleshooting guides, and production support documentation.
  • Production Support & Troubleshooting: Troubleshoot electrical, electronic, firmware configuration, and test-related issues during production. Collaborate closely with engineering, suppliers, technicians, operators, and manufacturing teams to quickly identify and resolve production bottlenecks.
  • Electronics Testing and Troubleshooting: Perform board-level and system-level debugging using oscilloscopes, multimeters, logic analyzers, power supplies, CAN analyzers, and other laboratory equipment.
  • Yield Improvement & Failure Analysis: Analyze manufacturing and test data to identify improvement opportunities. Lead root cause investigations, perform failure analysis on non-conforming products, and implement corrective actions to improve quality, reliability, and manufacturing performance.
  • Configuration & Change Implementation: Support engineering change implementation activities, manufacturing validation, revision updates, and configuration control processes to ensure accurate product builds.
  • Supplier Support: Work with suppliers to resolve electronics component, assembly, quality, and manufacturing issues. Support first article inspections, qualification activities, and corrective action investigations as required.
  • Engineering & Manufacturing Integration: Serve as the primary technical interface between Product Development and Manufacturing during product builds, new product introduction, production ramp-up, and ongoing production support. Coordinate issue resolution across Engineering, Quality, Operations, Supply Chain, Suppliers, and Manufacturing teams.
  • Ability to travel domestically and internationally 10-15%.
Education and Experience
  • Bachelor's degree in Electrical Engineering, Electronics Engineering, Mechatronics Engineering, or equivalent experience.
  • Ten or more years of experience in electronics manufacturing, manufacturing engineering, new product introduction, product development support, production support, or related engineering roles.
  • Understanding of electronic systems and assemblies, with the ability to evaluate issues across electrical, mechanical, firmware, software, and manufacturing disciplines.
  • Ability to read and interpret PCB schematics, PCB layout drawings, wiring diagrams, assembly drawings, and test procedures, and apply that knowledge to understand design intent and support manufacturing, testing, troubleshooting, and production support activities.
  • Experience using electronic test and diagnostic equipment including: OscilloscopesDigital multimetersLogic analyzersPower suppliesSignal generators
  • Experience soldering, reworking, and troubleshooting SMT and through-hole electronic assemblies.
  • Working knowledge of communication protocols including: I2CSPIUARTCAN/CANopenEthernet
Get your free, confidential resume review.

or drag and drop your file here.

Similar jobs

Similar jobs worth comparing

Electronics Technician
Electronics Technician

TD Williamson in • Salt Lake City (UT)

On-site
USD 36,000 - 54,000
Electro-Mechanical Technician
Electro-Mechanical Technician

T.D. Williamson • Salt Lake City (UT)

On-site
USD 52,000 - 76,000
Manufacturing Test Engineer
Manufacturing Test Engineer

Adecco • San Antonio (TX)

On-site
USD 70,000 - 90,000
Electrical Engineer
Electrical Engineer

Mirion Technologies • Florham Park (NJ)

On-site
USD 85,000 - 110,000
Electronics Technician
Electronics Technician

T.D. Williamson, Inc. • Salt Lake City (UT)

On-site
USD 32,000 - 46,000
Electrical Engineer
Electrical Engineer

Capintec • Florham Park (NJ)

On-site
USD 75,000 - 105,000
Sustaining Engineer
Sustaining Engineer

01 TDW (US), Inc. • Tulsa (OK)

On-site
USD 90,000 - 120,000
Electro-Mechanical Technician
Electro-Mechanical Technician

T.D. Williamson, Inc. • Salt Lake City (UT)

On-site
USD 55,000 - 90,000
Mechanical Engineer I
Mechanical Engineer I

TD Williamson • Tulsa (OK)

On-site
USD 65,000 - 90,000
Electrical Manufacturing Engineer - NPI & Process Optimizer
Electrical Manufacturing Engineer - NPI & Process Optimizer

TDW • Tulsa (OK)

On-site
USD 90,000 - 125,000