Electrical Assembler

ADDMAN Engineering LLC; New York (NY); On-site; USD 25,000 - 39,000; Full time

Job summary

ADDMAN Engineering LLC is seeking an Electrical Assembler to operate equipment and perform manual soldering and assembly to build and test an electrical coil assembly per customer specs.

You will set up coil winding equipment, solder coils and PCBs, and prepare wiring systems. Knowledge of IPC J-STD-001 and related aerospace quality standards is valued; training is available. Safety gear and strict procedure adherence are required.

Qualifications

• High School diploma or equivalent.
• Ability to read meters, gauges, charts, and instruments.
• Soldering experience to IPC J-STD-001 with Space Addendum preferred; training may be provided.
• Must be self-motivated and able to work without supervision.
• Interest in aerospace quality and compliance.

Responsibilities

• Setup and operate manual and automated coil winding equipment.
• Prepare and solder coil and PCB assemblies.
• Set up and operate manual and semi-automatic wire stripping machines.
• Operate Thermal Chamber, RF Pre-heater and Transfer Molding Press.
• Pot coil assemblies with two-part epoxy encapsulant.
• Trim, clean and inspect assemblies.
• Perform dielectric and resistance testing with stand-alone or semi-automated systems.
• Install and test crimp connectors and document results.
• Identify and communicate quality issues promptly.
• Log required information in Epicor ERP and maintain documentation.
• Maintain housekeeping; participate in lean opportunities.
• Read and understand drawings, work instructions and specifications.
• Complete HR LG 01 Training Matrix procedures and required trainings.

Skills

Meter reading

Soldering IPC J-STD-001

Reading drawings

Quality focus

Self-motivated

Communication

Education

High School diploma

Job description

Description

Job Summary

The Electrical Assembler operates equipment and performs manual soldering and assembly processes required to build and test an electrical coil assembly to customer specifications.

Primary Duties and Responsibilities

• Setup and operation of manual and automated coil winding equipment
• Preparation and soldering of coil and PCB assemblies
• Setup and operation of manual and semi-automated wire stripping machines
• Setup and operation of a Thermal Chamber, RF Pre-heater and Transfer Molding Press
• Potting of coil assemblies with two part epoxy encapsulant
• Manual trimming, cleaning and inspection of assemblies.
• Performance of dielectric and resistance testing using stand alone or semi-automated systems
• Installation and testing of crimp connectors
• Identification and communication of quality issues
• Accurate and timely completion of all job related documentation. Logging required information in Epicor (Enterprise Resource Planning (ERP) System).
• General Housekeeping in assigned work areas, evaluate and participate in lean opportunities
• Employees must be able to read and understand drawings, work instructions and applicable specifications.
• Complete review of all procedures related to your job per “HR LG 01 Training Matrix”
• Completion within time stated of all training required by Job Description in “HR LG 01 Training Matrix”

Note: All operations have work instructions which must be followed. Some also have customer drawings and/or specifications which also apply.

This is not an inclusive list of duties and responsibilities

Requirements

MINIMUM EDUCATION, EXPERIENCE, KNOWLEDGE, SKILLS and ABILITIES:

• High School diploma or equivalent
• Capable of reading and interpreting meters, gauges, charts, and a variety of instruments
• Experience with or Certification of soldering to IPC J-STD-001 with the Space Addendum, IPC-A-610 and IPC/WHMA-A-620 Modules 1 and 2 is desired. Training can / will be provided to otherwise qualified candidates.
• Must be self-motivated and able to work without direct supervision.
• Meticulous attention to detail. The products produced under this position are all aerospace related. Quality and compliance is critical at all phases of production.
• Well organized and strong verbal communication skills

WORK ENVIRONMENT:

• The performance of this position will require exposure to the manufacturing areas where all areas require the use of personal protective equipment such as safety glasses, hearing protection, steel toe shoes, and other mandatory safety equipment.
• For the most part, ambient temperatures with typical plant lighting and manufacturing equipment are present throughout the facility.

PHYSICAL DEMANDS:

• Sit or stand as needed.
• Walking primarily on a level surface for periodic periods throughout the day.
• Reaching above shoulder height, below the waist, or lifting as required to reach documents or store materials throughout the workday.
• Proper lifting techniques required.
• Ability and comfortability to work in small confine spaces while following proper safety protocol.
• Ability to accomplish the physical requirements of the position with or without reasonable accommodation.

SAFETY AND POLICY PRACTICES:

Each employee must be knowledgeable of standard safety policies and procedures and adhere to the same while supporting the goals and objectives of the organization and recognizing the Company’s need to achieve its business objectives. Each employee is responsible for complying with company hazardous waste disposal procedures.

ITAR REQUIREMENTS:

To conform to U.S. export control regulations, applicant should be eligible for any required authorizations from the U.S. Government.

AFFIRMATIVE ACTION:

ADDMAN Engineering is proud to be an Equal Opportunity Employer of Minorities, Women, Protected Veterans, and Individuals with Disabilities. All terms and conditions of employment will be administered without regard to an individual’s sex, gender identity, sexual orientation, race, color, religious creed, national origin, physical or mental disability, protected veteran status, or any other characteristic protected by applicable law.

NOTE: This job description is intended to describe the general level of work being performed. This job description is not intended to be all-inclusive. The duties of this position may change from time to time, and the employee may perform other related duties to meet the ongoing needs of the organization. ADDMAN Engineering reserves the right to add, delete or modify these duties and responsibilities at its discretion. Reasonable accommodations may be made to enable individuals with disabilities to perform the essential functions of this position. Employment is at-will, and nothing in this job description is intended to create or imply a contractual relationship or alter the at-will status of the employee.