Boyd Thermal by Eaton - Saw Operator I

Boyd; Laconia (NH); On-site; USD 22,000 - 33,000; Full time

Job summary

Boyd Corp in Laconia, NH is seeking a Saw Room Operator to operate saw equipment and cut materials to length per customer specifications. You will maintain quality and safety standards while supporting related machining tasks and housekeeping.

Typical duties include verifying documents, adjusting settings, replacing blades, and performing quality checks to ensure conformance to prints and customer requirements.

Qualifications

• High School diploma or equivalent preferred, plus 1-2 years of manufacturing experience.
• Ability to read, write and comprehend basic work instructions.
• Blue Print Reading and basic shop math skills.

Responsibilities

• Operate saw equipment in the Saw Room to cut materials to length per customer specifications.
• Verify paperwork, programs, and print revisions for accuracy before running a job.
• Run parts safely and efficiently, clocking in/out according to work order sequence.
• Maintain equipment, change saw blades, and ensure safe, correct operation.
• Perform quality audits to ensure product meets customer specifications.

Skills

Blueprint Reading

Shop Math

Reading & Comprehension

Education

High School diploma or equivalent

Tools

CNC Machinery

Sawing Equipment

Measuring Equipment

Job description

Job Description

Job Title: Saw Room Operator Updated: March 10, 2026

Typically Reports to: Shift Supervisor Depart: Saw Room

Location: Laconia Facility

I. Job Purpose

Operate the saw equipment used in the saw room to cut materials to length per customer specifications. Handle in a specified manor to accommodate any cosmetic requirements. Responsible for maintaining quality and safety standards, housekeeping, process integrity, monitoring of calibration of all measuring equipment used and monitoring machinery and tools to ensure safe correct and optimum performance, while maintaining professional conduct in the workplace. Cross train in Sanding, Debur, Punch, Straightening, CNC and Drilling, which are part of the Machining dept.

Ii. Key Accountabilities

• Get job assignment and communicate with the previous operator briefly, before the beginning of the shift.
• Before starting the machine, perform a quick check to ensure that safe and correct operations of the machine is possible and setup CNC manual and automatic cut off saws as required.
• Maintain equipment in the Saw Room, including changing filters for saw chip system.
• Verify the paperwork, print number, revision levels, operation sequence, materials, program and check sheet are all correct and consistent.
• To ensure that the check sheet dimensions are consistent with the print, run the first set of parts and check the parts dimensions against the print.
• Run jobs in an efficient, organized and safe manner, meeting or exceeding the hourly rate, while following the work instructions on the print and/or work order sequence. Must clock in and out of the work order and sequence.
• Maintain the workflow and perform quality audits as required to ensure that the product meets or exceeds the customer specifications.
• Make adjustments as required, with proper authorization.
• Change dull or broken saw blades using appropriate procedures.

III. Job Scope

• Job Complexity: Ability to apply common sense understanding to carry out detailed, but uninvolved written or oral instructions. Ability to deal with a few concrete variables in standardized and controlled situations.
• Supervisory Responsibility: Receives general instructions on routine work, detailed instructions on new assignments.
• Contacts/Interaction: Frequently works with peers and occasionally interfaces with management.
• Decision Making : Has minimal decision-making responsibility. Failure to make accurate decisions will have a low impact on the department’s success. Has a wide variety of resources available from which to make decisions.

IV. Job Qualifications

• Educational Background (minimum level needed to perform) and/or Previous Work Experience (minimal level years and what kind)

High School diploma or equivalent preferred, plus 1-2 years of manufacturing experience.

• Special Skills and Abilities (computer, language, interpersonal skills, etc.)

Ability to read write and comprehend basic work instructions and communications. Ability to follow written work instructions and directions. Basic understanding and comprehension of technical language tools and specifications.

Blue Print Reading

Basic Shop Math

• Ability to stand for 7.5 hours or more on concrete floors, ability to lift 35lb or more if team lift. Ability to hold parts, some heavy, for long periods of time if sanding or cutting.
• Licenses Needed, Certifications, Special Training Courses
  None

EEO EMPLOYER

All Job Posting Locations

Laconia

Remote Type

On-Site

EEO Statement

Boyd Corp is an equal opportunity employer. We celebrate diversity and are committed to creating an inclusive environment for all employees.