Associate Electrical Engineer

Heaviside Industries

California

On-site

USD 85,000 - 130,000

Full time

14 days+

A complete application in a minute

Tailored resume and cover letter, ready to send.

Get past ATS filters

Job summary

Heaviside Industries is seeking an Electrical Harness Designer to build and certify wiring harnesses for small unmanned vehicles. You will translate requirements into schematics, select connectors, route power and signals, and drive reliability from prototype to production.

You will troubleshoot on the bench and in the field, diagnose faults from wiring to software interfaces, and work with production teams to formalize build instructions. A BS in EE and hands-on harness experience are required.

Qualifications

  • BS in Electrical Engineering or closely related field.
  • 1 to 3 years of hands-on experience with vehicle wiring and harness design.
  • Formula SAE or Baja experience.
  • You have designed at least one complete harness from a blank page through build and debug, not just modified someone else’s.
  • PCB design experience (Altium).
  • Comfortable with a multimeter, an oscilloscope, a crimper, and a soldering iron.
  • Self-starter: you work autonomously, ask good questions early, and do not wait to be told what to do next.
  • U.S. Person as defined by ITAR (22 CFR §120.62)

Responsibilities

  • Design wiring harnesses for small unmanned vehicles from the ground up: requirements, schematics, pinouts, connector selection, wire gauge and circuit protection, shielding and grounding
  • Read harness schematics and sensor datasheets, work out what each sensor needs for power, signal, and grounding, and route power to it safely
  • Troubleshoot vehicles on the bench and in the field: shorts, opens, intermittent connections, bad crimps, ground problems, and electrical noise
  • Root-cause sensor or motor problems end to end—when a sensor or motor stops working, isolate whether the fault is the sensor, the connector, the cable, the power, or the software talking to it
  • Take harnesses from prototype to production: formal drawings, formboard layouts, BOMs, labeling, and build and test instructions a technician or contract manufacturer can follow
  • Define and run harness acceptance tests (continuity, pull) and vehicle-level electrical checkout
  • Support builds on the floor, review technician work, guide technicians, and fold what you learn back into the design

Skills

Vehicle wiring design
Harness design
Self-starter
Problem solving

Education

BS in Electrical Engineering

Tools

Altium
Multimeter
Oscilloscope
Crimping tool
Soldering iron

Job description

ABOUT HEAVISIDE INDUSTRIES

Heaviside Industries builds multi-domain autonomous precision munitions for U.S. and allied special operations and conventional forces. While modern warfare has rapidly evolved with the proliferation of unmanned systems, hyper-precise munitions in contested environments are the future of the battlefield. Economical precision strike capabilities are critical to U.S. and allied war efforts, enabling successful defeat of enemy military assets and infrastructure. Heaviside builds precision munitions designed to operate in GPS-denied and spectrum-jammed battlefields—where traditional systems degrade or fail—without inflated prices or sacrifice to performance.

All engineering and manufacturing is conducted in-house in Heaviside’s Los Angeles, CA headquarters and Oslo, Norway office.

Heaviside is backed by Interlagos, Menlo Ventures, Flume Ventures, Cantos, Anorak Ventures, and Ravelin Ventures.

WHAT YOU WILL DO
  • Design wiring harnesses for small unmanned vehicles from the ground up: requirements, schematics, pinouts, connector selection, wire gauge and circuit protection, shielding and grounding

  • Read harness schematics and sensor datasheets, work out what each sensor needs for power, signal, and grounding, and route power to it safely

  • Troubleshoot vehicles on the bench and in the field: shorts, opens, intermittent connections, bad crimps, ground problems, and electrical noise

  • Root-cause sensor or motor problems end to end—when a sensor or motor stops working, isolate whether the fault is the sensor, the connector, the cable, the power, or the software talking to it

  • Take harnesses from prototype to production: formal drawings, formboard layouts, BOMs, labeling, and build and test instructions a technician or contract manufacturer can follow

  • Define and run harness acceptance tests (continuity, pull) and vehicle-level electrical checkout

  • Support builds on the floor, review technician work, guide technicians, and fold what you learn back into the design

WHAT WE ARE LOOKING FOR
  • BS in Electrical Engineering or a closely related field

  • 1 to 3 years of hands‑on experience with vehicle wiring and harness design

  • Formula SAE or Baja experience

  • You have designed at least one complete harness from a blank page through build and debug, not just modified someone else’s

  • PCB design experience (Altium)

  • Comfortable with a multimeter, an oscilloscope, a crimper, and a soldering iron

  • Self‑starter: you work autonomously, ask good questions early, and do not wait to be told what to do next

  • U.S. Person as defined by ITAR (22 CFR §120.62)

Additional Information:

Compensation bands are determined by role, level, location, and alignment with market data. Individual level and base pay is determined on a case‑by‑case basis and may vary based on job‑related skills, education, experience, technical capabilities and internal equity. In addition to base salary, for full‑time hires, you may also be eligible for long‑term incentives, in the form of stock options, and access to medical, vision & dental coverage as well as access to a 401(k) retirement plan.

To conform to U.S. Government space technology export regulations, including the International Traffic in Arms Regulations (ITAR) you must be a U.S. citizen, lawful permanent resident of the U.S., protected individual as defined by 8 U.S.C. 1324b(a)(3), or eligible to obtain the required authorizations from the U.S. Department of State. Learn more about the ITAR here.

(https://www.pmddtc.state.gov/?id=ddtc_kb_article_page&sys_id=24d528fddbfc930044f9ff621f961987)

Heaviside is an Equal Opportunity Employer; employment with Heaviside is governed on the basis of merit, competence and qualifications and will not be influenced in any manner by race, color, religion, gender, national origin/ethnicity, veteran status, disability status, age, sexual orientation, gender identity, marital status, physical disability or any other legally protected status.

Get your free, confidential resume review.

or drag and drop your file here.

Similar jobs

Similar jobs worth comparing

Harness Design Engineer for Autonomous Munitions
Harness Design Engineer for Autonomous Munitions

Heaviside Industries, Inc. • Los Angeles (CA)

On-site
USD 90,000 - 130,000
Stock options
Medical, vision & dental coverage
401(k) retirement plan
Harness Design Engineer
Harness Design Engineer

Heaviside Industries, Inc. • Los Angeles (CA)

On-site
USD 90,000 - 130,000
Stock options
Medical, vision & dental coverage
401(k) retirement plan
Harness Design Engineer
Harness Design Engineer

Heaviside Industries • Los Angeles (CA)

On-site
USD 90,000 - 125,000
Stock options
401(k) plan
Medical, vision & dental coverage
Electrical Engineer
Electrical Engineer

Heaviside Industries • California

On-site
USD 120,000 - 210,000
Electrical Engineer
Electrical Engineer

Heaviside Industries • Los Angeles (CA)

On-site
USD 120,000 - 170,000
Stock options
Medical, vision & dental
401(k) plan
+1
R&D Mechanical Technician
R&D Mechanical Technician

Heaviside Industries, Inc. • California

On-site
USD 85,000 - 125,000
Mechanical Engineer
Mechanical Engineer

Heaviside Industries • Los Angeles (CA)

On-site
USD 70,000 - 90,000
Medical, vision & dental coverage
401(k) retirement plan
Stock options
Electrical Engineer
Electrical Engineer

Heaviside Industries • Los Angeles (CA)

On-site
USD 120,000 - 180,000
Stock options
Medical, Vision & Dental coverage
401(k) retirement plan
R&D Mechanical Technician
R&D Mechanical Technician

Heaviside Industries • Los Angeles (CA)

On-site
USD 75,000 - 110,000
Stock options
Medical, vision & dental coverage
401(k)
Senior Embedded Software Engineer
Senior Embedded Software Engineer

Heaviside Industries, Inc. • Los Angeles (CA)

On-site
USD 140,000 - 190,000