Associate Systems Engineer (Product Development)

AVETICS GLOBAL PTE. LTD.; Singapore; On-site; SGD 50,000 - 70,000; Full time

Job summary

AVETICS GLOBAL PTE. LTD. is seeking an Associate Systems Engineer (Product Development) to support the R&D team in building, bringing up, and testing new hardware for remote power delivery systems.

This bench and lab role involves prototyping, test rig setup, and data-driven feedback to design engineers. The candidate should be hands-on, methodical with data, and comfortable collaborating with electrical, mechanical, and firmware engineers.

Qualifications

• Diploma in Electrical Engineering, Electronics Engineering, Mechatronics, or a related discipline.
• 0 to 2+ years of hands-on experience building or testing electronic hardware.
• Ability to interpret schematics, wiring diagrams, mechanical drawings, and datasheets.
• Competent with hand soldering, crimping, and harness assembly.
• Willingness to travel occasionally and work in field environments.

Responsibilities

• Build, wire, and bring up prototype hardware - harnesses, sub-assemblies, and full system integrations.
• Integrate mechanical, electrical, and firmware subsystems into working prototypes and support design iterations between revisions.
• Set up and operate lab equipment: oscilloscopes, power supplies, electronic loads, DAQ, thermal cameras, load cells.
• Design and build test jigs, fixtures, and rigs for repeatable bench testing.
• Run characterisation, endurance, and verification tests; record results and write up findings clearly enough for someone else to act on.
• Support environmental, EMC, and safety pre-compliance testing, both in-house and at external labs.
• Perform calibration of sensors and instrumented subsystems.
• Troubleshoot hardware and firmware issues down to board and component level, and document root cause.
• Maintain BOMs, wiring schedules, build records, and revision histories for prototype units.
• Assist with the development of build instructions, test procedures, and standard operating procedures for handover to production.
• Support field trials and customer demonstrations when required.
• Any other duties as assigned by the supervisor from time to time.

Skills

Troubleshooting

Data recording & presentation

Hands-on hardware assembly

Schematic & datasheet interpretation

Travel readiness

Education

Diploma in Electrical/Electronics/Mechatronics

Tools

Altium

KiCad

SolidWorks

Fusion 360

ST-Link

Logic analyzers

CAN bus debugging tools

Job description

Associate Systems Engineer (Product Development)

The Associate Systems Engineer supports the R&D team in building, bringing up, and testing new hardware for remote power delivery systems. This is a bench and lab role rather than a field operations role: you will be building prototypes, setting up test rigs, running characterisation and verification tests, and feeding results back to the design engineers. The ideal candidate is hands-on, methodical about data, and comfortable working with electrical, mechanical, and firmware engineers on the same problem.

Key Responsibilities

• Build, wire, and bring up prototype hardware - harnesses, sub-assemblies, and full system integrations
  
• Integrate mechanical, electrical, and firmware subsystems into working prototypes and support design iterations between revisions
  
• Set up and operate lab equipment: oscilloscopes, power supplies, electronic loads, DAQ, thermal cameras, load cells
  
• Design and build test jigs, fixtures, and rigs for repeatable bench testing
  
• Run characterisation, endurance, and verification tests; record results and write up findings clearly enough for someone else to act on
  
• Support environmental, EMC, and safety pre-compliance testing, both in-house and at external labs
  
• Perform calibration of sensors and instrumented subsystems
  
• Troubleshoot hardware and firmware issues down to board and component level, and document root cause
  
• Maintain BOMs, wiring schedules, build records, and revision histories for prototype units
  
• Assist with the development of build instructions, test procedures, and standard operating procedures for handover to production
  
• Support field trials and customer demonstrations when required
  
• Any other duties as assigned by the supervisor from time to time
  

Minimum Qualifications

• Diploma in Electrical Engineering, Electronics Engineering, Mechatronics, or a related discipline
• 0 to 2+ years of hands-on experience building or testing electronic hardware
• Ability to interpret schematics, wiring diagrams, mechanical drawings, and datasheets
• Competent with hand soldering, crimping, and harness assembly
• Strong troubleshooting and problem-solving skills, with the discipline to isolate variables rather than guess
• Comfortable recording and presenting test data
• Willingness to travel occasionally and work in field environments

Preferred Qualifications

• Experience with high-voltage DC systems and the safety practices that go with them
• Familiarity with motor drives, BLDC control, or power electronics
• Exposure to CAN bus, serial protocols, or embedded debugging tools (ST-Link, logic analysers)
• Basic scripting for test automation and data processing (Python preferred)
• Familiarity with ECAD or MCAD tools (Altium, KiCad, SolidWorks, Fusion 360)
• Awareness of relevant standards such as IEC 62368-1, CISPR 32/EN 55032, or MIL-STD-810
• Experience with unmanned systems or custom robotics builds