Senior Electrical Test Engineer

Haemonetics; Batu Kawan; On-site; MYR 180,000 - 280,000; Full time

Job summary

Haemonetics is seeking a hands-on Test Engineer to design, develop, verify and release electrical test fixtures for PCBAs and sub-assemblies. You will interface with contract manufacturers for ICT/FCT systems and strengthen in-house test capability.

The role requires 5–10 years in manufacturing test engineering, proficiency in NI LabVIEW, and experience with fixture development, verification, and documentation in a regulated environment.

Qualifications

• Bachelor's or Master in Electrical Engineering or related field.
• 5–10 years in manufacturing test engineering, preferably medical devices.
• Experience with ICT/FCT development and debug.
• Proficient in NI LabVIEW for test automation.

Responsibilities

• Design, develop, verify, validate, and release electrical test fixtures.
• Maintain and improve fixtures on production lines.
• Interface with contract manufacturers on ICT/FCT systems.
• Develop automated test software using LabVIEW and scripting (Python/C/C++).
• Support fixture calibration, maintenance, and spares.

Skills

LabVIEW Automation

Schematic Reading

Electrical Troubleshooting

Cross-functional Collaboration

Education

Bachelor's or Master in Electrical Engineering

Tools

Keysight 3070

Teradyne Test Station

OrCAD

Altium

Python

C/C++

Job description

We are constantly looking to add to our core talent. If you are seeking a career that is challenging and rewarding, a work environment that is diverse and dynamic, look no further — Haemonetics is your employer of choice.

Role Overview

This is a hands‑on technical role. The successful candidate will:

• Design, develop, verify, validate, and release new electrical test fixtures
• Maintain, troubleshoot, and improve existing fixtures used in production
• Serve as the technical interface to contract manufacturers on their ICT and FCT systems
• Strengthen in‑house test capability, including duplicating key contract manufacturer testers on site where needed

Key Responsibilities

Test Fixture Design & Development

• Define test requirements, test strategy, and test coverage for PCBAs and electrical sub‑assemblies
• Design test fixture electronics, including schematic capture, PCB layout, and prototype interface boards
• Develop ICT, FCT, and In‑System Programming (ISP) test solutions, including fixture hardware, wiring, and instrumentation
• Develop and maintain automated test software using NI LabVIEW (TestStand, Python, or C/C++ where appropriate)
• Apply Design for Manufacturability (DFM) and Design for Test (DFT) principles, review product schematics and PCB layouts for testability

Verification, Validation & Documentation

• Plan and execute fixture verification and validation (IQ/OQ/PQ, test software validation, Gage R&R where required)
• Create clear documentation: test specifications, theory of operation, schematics, work instructions, and troubleshooting guides
• Release fixtures and documentation through Agile PLM using change control (ECOs) in line with ISO 13485 and the Quality Management System

Production & Fixture Sustaining Support

• Maintain and troubleshoot existing fixtures on the Penang production line and support Clinton, PA
• Perform hands‑on electrical and mechanical debug using oscilloscopes, function generators, DMMs, power supplies, electronic loads, and DAQ
• Analyze test data and failures, drive root cause analysis, corrective actions, and first‑pass yield improvement
• Support fixture calibration, preventive maintenance, spares, and obsolescence planning
• Train and support technicians and operators on fixture use and troubleshooting

Contract Manufacturer & Supplier Interface

• Act as the technical point of contact for contract manufacturer ICT/FCT issues in Malaysia, Australia, and other regions
• Review CM test coverage, programs, and changes, support test‑related ECOs and supplier change notifications (SCNs)
• Where needed, duplicate CM testers in‑house to support failure analysis and business continuity

Continuous Improvement & Automation

• Improve test reliability, cycle time, and coverage through automation (electrical and mechanical)
• Modernize legacy test systems and standardize fixture design practices across sites
• Support reliability and stress testing fixtures as required

Cross‑Functional Collaboration

• Partner with Electrical, Mechanical, Software, Manufacturing, Quality, and Supply Chain teams
• Work effectively across global time zones, especially with Boston‑based R&D, travel as needed (approximately 10–15%)

Qualifications

• Bachelor’s or Master’s degree in electrical / Electronic Engineering or related field
• 5–10 years of experience in manufacturing test engineering, preferably in medical devices or other high‑reliability industries (e.g., automotive, aerospace)
• Proven ICT and FCT development and debug experience (e.g. Keysight/Agilent 3070, Teradyne Test Station, or similar)
• Strong proficiency in NI LabVIEW for test automation
• Mandatory: hands‑on experience designing test fixture PCBs – schematic capture, layout, and prototyping
• Expert‑level electrical and mechanical troubleshooting using standard lab test equipment
• Strong ability to read, review, and analyze schematics, PCB layouts, and assembly drawings
• Experience with fixture verification and validation and controlled documentation release (Agile PLM preferred)
• Experience working in regulated environments (ISO 13485; IEC 60601 awareness)
• Experience supporting contract manufacturers and production lines
• NI TestStand; Certified LabVIEW Developer (CLD) or higher
• FPGA development experience
• Python, C/C++, or other instrument‑control programming
• Schematic and layout tools such as OrCAD, Altium, or equivalent
• Experience with electromechanical systems (motors, sensors, power supplies)

Skills & Competencies

• Strong technical depth and a hands‑on, problem‑solving mindset
• Structured and disciplined approach to documentation and quality systems
• Clear and effective communication in English (written and verbal) Bahasa Malaysia or Mandarin is an advantage
• Ability to work independently and collaboratively in a global organization
• Ability to manage multiple priorities across sites and partners

Why This Role Matters: Reliable test fixtures protect product quality and patient safety. This role is critical to building strong test engineering capability in Malaysia and to delivering high‑quality, compliant medical devices to patients worldwide.

EEO Policy Statement