Moulding Process Engineering Technician

Ei Electronics

Shannon

Remote

EUR 42,000 - 64,000

Full time

2 days ago
Be an early applicant

Get a reply from this employer

Your resume and cover letter, tailored to exactly what they’re hiring for.

Get past ATS filters

Job summary

Ei Electronics in Shannon, Co. Clare, Ireland is seeking a hands-on Moulding Process Engineering Technician with proven injection moulding and mould-setting experience.

You will work with Production, Quality and Maintenance to implement and improve moulding processes to deliver consistent quality, output and yield. You will set up machines, run start-up checks, optimise parameters, troubleshoot defects, monitor performance, and support trials and process validation.

Qualifications

  • At least three years in high-volume injection moulding with hands-on process setup and optimisation.

Responsibilities

  • Carry out mould changes including tool removal, installation, clamping, alignment and connection of cooling, electrical and hot-runner services.
  • Set up injection moulding machines, robotic handling systems, hoppers, dryers and associated equipment.
  • Perform start-up checks and obtain first-off quality approval before production release.
  • Establish and optimise moulding parameters (temperature, injection speed/pressure, holding pressure, cooling time and clamp settings).
  • Troubleshoot defects such as short shots, flash, sink marks, warpage and burn marks and identify root causes.
  • Monitor process performance to improve cycle times, scrap levels, yield and OEE while maintaining quality.
  • Ensure correct material handling and controlled use of regrind per specifications.
  • Support trials, new moulds and process validation; document settings and results.
  • Maintain setup/changeover records and troubleshooting logs.
  • Provide clear handovers between shifts.
  • Collaborate with Tooling and Maintenance to resolve mould/equipment issues; escalate when needed.
  • Train operators and mould setters; support continuous improvement and faster changeovers.
  • Follow safety procedures and maintain housekeeping and compliance.

Skills

Injection moulding
Process setup
Troubleshooting
Quality assurance
Safety compliance
Team collaboration
Documentation

Education

Engineering qualification
Polymer-processing qualification
Level 7+ polymer/mechanical/manufacturing qualification
Trade qualification (practical moulding)

Tools

Injection moulding machines
Robotic handling systems
Hoppers and dryers
Hot-runner systems
Measurement equipment

Job description

Department : Manufacturing
Location : Shannon, Co. Clare, Ireland
Employment Type : Full Time, Permanent

The Opportunity

Ei Electronics is seeking a hands-on Moulding Process Engineering Technician with proven injection moulding and mould-setting experience. Working in a team environment with Production, Quality & Maintenance, you will be directly responsible for moulding processes implementations and improvement with an aim to deliver consistent component quality, output and yield.

What you will be responsible for
  • Carry out mould changes, including tool removal, installation, clamping, alignment and connection of cooling, electrical and hot-runner services, where applicable.
  • Set up of injection moulding machines, robotic handling systems, hoppers, dryers and associated equipment.
  • Complete start-up checks and obtain first-off quality approval before production release.
  • Establish and optimise moulding parameters, including temperatures, injection speed and pressure, holding pressure, cooling time and clamp settings, within approved process limits.
  • Troubleshoot defects such as short shots, flash, sink marks, warpage and burn marks using a structured approach to identify and resolve root causes.
  • Monitor process performance and improve cycle times, scrap levels, yield and overall equipment effectiveness while maintaining product quality.
  • Ensure correct material identification, drying, handling and controlled use of regrind in accordance with approved specifications.
  • Support trials, new mould introductions and process validation; document settings, results and approved processing windows.
  • Maintain accurate setup, changeover records and troubleshooting logs.
  • Provide clear technical handovers between shifts.
  • Work with Tooling and Maintenance to resolve mould and equipment issues, identifying when specialist repair or maintenance support is required.
  • Train operators and mould setters in approved setup and operating methods; support continuous improvement and reduced changeover times.
  • Follow safe lifting, isolation and guarding procedures, and maintain good housekeeping and compliance with quality and safety requirements.
What we are looking for
Qualifications and Experience
  • At least three years of relevant experience in a high-volume injection moulding environment, including hands‑on process setup, troubleshooting and optimisation.
  • Proven mould-setting experience, with the ability to carry out safe mould changes and bring machines into stable production.
  • A relevant engineering or polymer‑processing qualification is desirable.
  • Candidates with a technical qualification, recognised trade qualification or equivalent practical moulding experience will also be considered.
  • For appointment at engineer level, a Level 7 or higher qualification in Polymer, Mechanical, Manufacturing or a related engineering discipline, or equivalent demonstrable engineering competence.
  • Practical understanding of thermoplastic materials, mould construction, cooling circuits and the effects of process parameters on component quality.
  • Experience setting up ancillary equipment, including robots, material dryers, loaders and temperature‑control units.
  • Ability to interpret setup sheets, technical drawings and quality specifications, and use relevant measurement equipment.
  • Computer literacy and the ability to record, analyse and communicate process information accurately.
  • Experience with hot‑runner systems, robotic part handling and changeover improvement.
  • Working knowledge of hydraulic, pneumatic and machine‑control systems sufficient to support process fault diagnosis.
Personal attributes
  • A practical, systematic approach to problem solving and a strong focus on quality and safety.
  • Clear communication and good interpersonal skills, with the ability to work constructively with operators and technical teams.
  • Initiative, ownership and the ability to prioritise effectively under production pressure.
  • Enthusiasm for developing others and improving manufacturing performance

At Ei Electronics you will work on technologies that make a real difference to people’s lives while building your career in an engineering organization renowned for quality, innovation, and technical excellence.

Join us and help shape the future of life safety, Connected Home, and IoT solutions.

Ei Electronics is an equal opportunity employer and is committed to fostering an inclusive anddiverseworkplace.

Get your free, confidential resume review.

or drag and drop your file here.

Similar jobs

Similar jobs worth comparing

Moulding Process Engineering Technician
Moulding Process Engineering Technician

Ei Electronics • Shannon

On-site
EUR 45,000 - 75,000
Moulding Process Technician - Injection & Quality Focus
Moulding Process Technician - Injection & Quality Focus

Ei Electronics • Shannon

Remote
EUR 42,000 - 64,000
Engineering Manager
Engineering Manager

ID Recruitment • Sligo

On-site
EUR 90,000 - 130,000
Performance bonus
Pension
Flexible holidays
+1
Process Engineer
Process Engineer

Mergon Group • Inishcrone

On-site
EUR 45,000 - 65,000
Process Engineer
Process Engineer

Mergon • Inishcrone

On-site
EUR 45,000 - 65,000
Senior Process Engineer
Senior Process Engineer

Nolato • Sligo

On-site
EUR 60,000 - 80,000
Advanced Injection Molding Process Technician
Advanced Injection Molding Process Technician

Ei Electronics • Shannon

On-site
EUR 45,000 - 75,000
Process Engineer
Process Engineer

MGS Mfg. Group Ltd. • Leixlip

On-site
EUR 60,000 - 80,000
Subsidised healthcare plan
Private pension scheme
Discounted onsite gym and canteen
Moulding Technician
Moulding Technician

Inform3 • Conna

On-site
EUR 50,000 - 60,000
Process Engineer
Process Engineer

MGS Mfg. Group • Leixlip

On-site
EUR 60,000 - 90,000
Subsidised healthcare plan
Private pension scheme
Onsite gym and canteen facilities
Top locations