Senior Embedded Software Engineer

SPT Labtech; Cambridge; On-site; GBP 90,000 - 120,000; Full time

Benefits offered by this job

Private medical insurance

Pension plan

Annual discretionary bonus

Job summary

SPT Labtech is seeking a Senior Embedded Software Engineer - Robotics to craft firmware that drives high-precision robotics and instruments. You will design motor control, integrate hardware via CAN and Ethernet, and help shape the firmware architecture for next-generation laboratory automation.

The role sits at our Melbourn site near Cambridge and involves collaboration with software, electronics and mechanical teams.

Qualifications

• Solid commercial experience in embedded software or firmware development.
• Hands-on C/C++ on ARM microcontrollers (Cortex-M).
• Experience defining module boundaries and interfaces between components.
• Practical experience implementing motor and actuator control in production hardware.
• Experience integrating third-party or OEM hardware modules.
• Confidence working across CAN, Ethernet, UART, SPI, I²C and GPIO.
• Working knowledge of C# .NET for device-facing PC-side code.
• Exposure to RTOS environments and debugging tools (oscilloscopes, logic analyzers, protocol analyzers).
• Reliability-focused design: fault detection, diagnostics and recovery mechanisms.
• Familiarity with Git, CI and unit testing.

Responsibilities

• Design, develop and maintain embedded software in C++ for ARM Cortex-M microcontrollers.
• Implement motor and actuator control across open-loop, closed-loop and hybrid schemes.
• Integrate modules and devices over CAN, Ethernet, UART, SPI, I²C and GPIO; write drivers.
• Shape firmware architecture: interfaces and module boundaries.
• Contribute to PC-side C# .NET code interfacing with embedded layer.
• Develop sensor signal acquisition and conditioning.
• Emphasize reliability, diagnostics and self-test for unattended operation.
• Troubleshoot and debug embedded software and hardware interfaces.
• Provide technical leadership and mentoring to junior engineers.
• Produce clear documentation: specifications, designs and user-facing material.

Skills

Embedded systems

C/C++ on ARM

System architecture

Troubleshooting hardware

Team mentoring

Education

Degree in electronics or CS

Equivalent experience

Tools

C# .NET

Git

Oscilloscopes

Logic analyzers

Protocol analyzers

JTAG/SWD debuggers

Job description

We are looking for a Senior Embedded Software Engineer - Robotics to write the code that brings our robots to life. Every instrument SPT Labtech ships from nanolitre-precision liquid handlers to fully automated sample management systems. This depends on firmware that drives motors with absolute precision, reads sensors in real time, and keeps complex robotic systems running reliably in labs around the world. In this role, your embedded C++ on ARM Cortex-M sits at the very heart of our products: you’ll design motor and actuator control, integrate robotic hardware over CAN and Ethernet, and shape the firmware architecture of our next generation of laboratory automation. Technology that directly accelerates scientific discovery and improves human health. This is an office and lab-based role at our Melbourn site, near Cambridge.

About us:

Based in Cambridge,makes products that transform the way scientists work. For decades, our expert scientists, engineers and business innovators have provided scientists with world-leading, innovative solutions for liquid handling, sample preparation, and sample management that help accelerate research and make a real difference to human health. We work collaboratively with our customers, building trusted relationships that enable us to deliver exceptional, personalised experiences designed for real-world challenges in the lab.

What you will be doing:

You’ll join a multidisciplinary R&D team where software, electronics and mechanical engineers sit side by side and designs come together in the lab, not just on paper. Day to day, you will:

• Design, develop and maintain embedded software in C++ for ARM Cortex-M series microcontrollers — firmware that ships inside real instruments.
• Implement motor and actuator control across open-loop, closed-loop and hybrid schemes, working hand in hand with our electronics team on motor drives and robotic hardware.
• Integrate OEM and third-party modules, barcode readers, thermal units, pneumatics and similar — over CAN, Ethernet, UART, SPI, I²C and GPIO, writing the device drivers that connect them into the system.
• Shape the firmware and system architecture: module boundaries, interfaces and the communications that tie distributed microcontrollers together.
• Contribute to the lower-level, device-facing C# .NET code on the PC side that talks to the embedded layer.
• Implement signal acquisition and conditioning for the sensors and transducers fitted throughout each instrument.
• Design in reliability from the outset, fault detection, diagnostics, recovery, watchdogs and built-in self-test, because our instruments run unattended in labs where results matter.
• Troubleshoot and debug complex embedded software, hardware interfaces and robotics system issues, including on the CAN bus.
• Provide technical leadership and mentoring to junior engineers, and help raise the bar for software development practice across the team.
• Produce clear technical documentation: specifications, designs, architecture and user-facing material.

About you

You’re an embedded engineer who thinks at the system level, comfortable reasoning about how distributed microcontrollers, timing and communications interact, not just single-component behaviour. You’re a proactive self-starter and a sharp problem-solver with the persistence to chase an issue to its root cause, and you communicate clearly across software, electronics and mechanical disciplines. You take pride in firmware that is robust, diagnosable and built to run reliably for years in the field.

Essential Requirements

• Solid commercial experience in embedded software or firmware development.
• Strong, hands-on C/C++ on ARM microcontrollers (Cortex-M series or similar).
• Demonstrable experience contributing to firmware and system architecture, defining module boundaries and interfaces between components, not just implementing to an existing design.
• Practical, hands-on experience implementing motor and actuator control in production hardware.
• A track record of integrating third-party or OEM hardware modules, including their bespoke controllers, into a larger system.
• Confidence working across CAN, Ethernet (TCP/UDP), UART, SPI, I²C and GPIO.
• Working knowledge of C# .NET, sufficient for device-facing PC-side code.
• Exposure to RTOS environments and standard embedded debugging tools such as oscilloscopes, logic analysers and protocol analysers.
• A disciplined approach to reliability: fault detection, diagnostics and recovery mechanisms.
• Comfortable with unit testing, continuous integration and version control (Git).

Desirable skills and experience

• Experience with JTAG/SWD debuggers and protocol analysers (CAN, Ethernet and similar) for hardware-level debugging.
• Field-oriented control (FOC) experience.
• Familiarity with gRPC or other distributed software architectures.
• Experience working in Agile teams.
• A degree in electronics, computer science or a related field, or equivalent experience.

Our commitment to you

We offer a competitive salary package and comprehensive, valued benefits, including private medical insurance, a generous pension plan, and an annual discretionary bonus.

We embrace diversity and inclusivity, regardless of race, ethnicity, gender, gender identity, sexual orientation, physical ability, or family status. We prioritise supporting our employees’ diverse needs as we strive for excellence together.